x86/boot: Fix kexec booting failure in the SEV bit detection code

ryncsn · suryasaimadhu · commit bdec8d7fa55e · 2018-09-27T19:35:03.000+02:00
Commit 1958b5f ("x86/boot: Add early boot support when running with SEV active") can occasionally cause system resets when kexec-ing a second kernel even if SEV is not active. That's because get_sev_encryption_bit() uses 32-bit rIP-relative addressing to read the value of enc_bit - a variable which caches a previously detected encryption bit position - but kexec may allocate the early boot code to a higher location, beyond the 32-bit addressing limit. In this case, garbage will be read and get_sev_encryption_bit() will return the wrong value, leading to accessing memory with the wrong encryption setting. Therefore, remove enc_bit, and thus get rid of the need to do 32-bit rIP-relative addressing in the first place. [ bp: massage commit message heavily. ] Fixes: 1958b5f ("x86/boot: Add early boot support when running with SEV active") Suggested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Kairui Song <kasong@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-kernel@vger.kernel.org Cc: tglx@linutronix.de Cc: mingo@redhat.com Cc: hpa@zytor.com Cc: brijesh.singh@amd.com Cc: kexec@lists.infradead.org Cc: dyoung@redhat.com Cc: bhe@redhat.com Cc: ghook@redhat.com Link: https://lkml.kernel.org/r/20180927123845.32052-1-kasong@redhat.com
diff --git a/arch/x86/boot/compressed/mem_encrypt.S b/arch/x86/boot/compressed/mem_encrypt.S
@@ -25,20 +25,6 @@ ENTRY(get_sev_encryption_bit)
 	push	%ebx
 	push	%ecx
 	push	%edx
-	push	%edi
-
-	/*
-	 * RIP-relative addressing is needed to access the encryption bit
-	 * variable. Since we are running in 32-bit mode we need this call/pop
-	 * sequence to get the proper relative addressing.
-	 */
-	call	1f
-1:	popl	%edi
-	subl	$1b, %edi
-
-	movl	enc_bit(%edi), %eax
-	cmpl	$0, %eax
-	jge	.Lsev_exit
 
 	/* Check if running under a hypervisor */
 	movl	$1, %eax
@@ -69,15 +55,12 @@ ENTRY(get_sev_encryption_bit)
 
 	movl	%ebx, %eax
 	andl	$0x3f, %eax		/* Return the encryption bit location */
-	movl	%eax, enc_bit(%edi)
 	jmp	.Lsev_exit
 
 .Lno_sev:
 	xor	%eax, %eax
-	movl	%eax, enc_bit(%edi)
 
 .Lsev_exit:
-	pop	%edi
 	pop	%edx
 	pop	%ecx
 	pop	%ebx
@@ -113,8 +96,6 @@ ENTRY(set_sev_encryption_mask)
 ENDPROC(set_sev_encryption_mask)
 
 	.data
-enc_bit:
-	.int	0xffffffff
 
 #ifdef CONFIG_AMD_MEM_ENCRYPT
 	.balign	8
