Porosity

Porosity or void fraction is a measure of the void spaces in a material, and is a fraction of the volume of voids over the total volume, between 0–1, or as a percentage between 0–100%. The term is used in multiple fields including pharmaceutics, ceramics, metallurgy, materials, manufacturing, earth sciences and construction.

Porosity in earth sciences and construction

Used in geology, hydrogeology, soil science, and building science, the porosity of a porous medium (such as rock or sediment) describes the fraction of void space in the material, where the void may contain, for example, air or water. It is defined by the ratio:

$\phi ={\frac {V_{V}}{V_{T}}}$

where V_V is the volume of void-space (such as fluids) and V_T is the total or bulk volume of material, including the solid and void components. Both the mathematical symbols $\phi$ and $n$ are used to denote porosity.

Porosity is a fraction between 0 and 1, typically ranging from less than 0.01 for solid granite to more than 0.5 for peat and clay. It may also be represented in percent terms by multiplying the fraction by 100.

The porosity of a rock, or sedimentary layer, is an important consideration when attempting to evaluate the potential volume of water or hydrocarbons it may contain. Sedimentary porosity is a complicated function of many factors, including but not limited to: rate of burial, depth of burial, the nature of the connate fluids, the nature of overlying sediments (which may impede fluid expulsion). One commonly used relationship between porosity and depth is given by the Athy (1930) equation:

$\phi (z)=\phi _{0}e^{-kz}\,$

where $\phi _{0}$ is the surface porosity, $k$ is the compaction coefficient (m⁻¹) and $z$ is depth (m).

A value for porosity can alternatively be calculated from the bulk density $\rho _{\text{bulk}}$ and particle density $\rho _{\text{particle}}$:

$\phi =1-{\frac {\rho _{\text{bulk}}}{\rho _{\text{particle}}}}$

Normal particle density is assumed to be approximately 2.65 g/cm³, although a better estimation can be obtained by examining the lithology of the particles.

Porosity and hydraulic conductivity

Porosity is indirectly related to hydraulic conductivity; for two similar sandy aquifers, the one with a higher porosity will typically have a higher hydraulic conductivity (more open area for the flow of water), but there are many complications to this relationship. Clays, which typically have very low hydraulic conductivity also have very high porosities (due to the structured nature of clay minerals), which means clays can hold a large volume of water per volume of bulk material, but they do not release water rapidly.

Sorting and porosity

Effects of sorting on alluvial porosity

Well sorted (grains of approximately all one size) materials have higher porosity than similarly sized poorly sorted materials (where smaller particles fill the gaps between larger particles). The graphic illustrates how some smaller grains can effectively fill the pores (where all water flow takes place), drastically reducing porosity and hydraulic conductivity, while only being a small fraction of the total volume of the material. For tables of common porosity values for earth materials, see the "further reading" section in the Hydrogeology article.

Porosity of rocks

Consolidated rocks (e.g. sandstone, shale, granite or limestone) potentially have more complex "dual" porosities, as compared with alluvial sediment. This can be split into connected and unconnected porosity. Connected porosity is more easily measured through the volume of gas or liquid that can flow into the rock, whereas fluids cannot access unconnected pores.

Porosity of soil

Porosity of surface soil typically decreases as particle size increases. This is due to soil aggregate formation in finer textured surface soils when subject to soil biological processes. Aggregation involves particulate adhesion and higher resistance to compaction. Typical bulk density of sandy soil is between 1.5 and 1.7 g/cm³. This calculates to a porosity between 0.43 and 0.36. Typical bulk density of clay soil is between 1.1 and 1.3 g/cm³. This calculates to a porosity between 0.58 and 0.51. This seems counterintuitive because clay soils are termed heavy, implying lower porosity. Heavy apparently refers to a gravitational moisture content effect in combination with terminology that harkens back to the relative force required to pull a tillage implement through the clayey soil at field moisture content as compared to sand.

Porosity of subsurface soil is lower than in surface soil due to compaction by gravity. Porosity of 0.20 is considered normal for unsorted gravel size material at depths below the biomantle. Porosity in finer material below the aggregating influence of pedogenesis can be expected to approximate this value.

Soil porosity is complex. Traditional models regard porosity as continuous. This fails to account for anomalous features and produces only approximate results. Furthermore it cannot help model the influence of environmental factors which affect pore geometry. A number of more complex models have been proposed, including fractals, bubble theory, cracking theory, Boolean grain process, packed sphere, and numerous other models. See also Characterisation of pore space in soil.

Types of geologic porosities

Primary porosity

The main or original porosity system in a rock or unconfined alluvial deposit.

Secondary porosity

A subsequent or separate porosity system in a rock, often enhancing overall porosity of a rock. This can be a result of chemical leeching of minerals or the generation of a fracture system. This can replace the primary porosity or coexist with it (see dual porosity below).

Fracture porosity

This is porosity associated with a fracture system or faulting. This can create secondary porosity in rocks that otherwise would not be reservoirs for hydrocarbons due to their primary porosity being destroyed (for example due to depth of burial) or of a rock type not normally considered a reservoir (for example igneous intrusions or metasediments).

Vuggy porosity

This is secondary porosity generated by dissolution of large features (such as macrofossils) in carbonate rocks leaving large holes, vugs, or even caves.

Effective porosity (also called open porosity)

Refers to the fraction of the total volume in which fluid flow is effectively taking place and includes Caternary and dead-end (as these pores cannot be flushed, but they can cause fluid movement by release of pressure like gas expansion) pores and excludes closed pores (or non-connected cavities). This is very important for groundwater and petroleum flow, as well as for solute transport.

Ineffective porosity (also called closed porosity)

Refers to the fraction of the total volume in fluids or gases are present but in which fluid flow can not effectively take place and includes the closed pores. Understanding the morphology of the porosity is thus very important for groundwater and petroleum flow.

Dual porosity

Refers to the conceptual idea that there are two overlapping reservoirs which interact. In fractured rock aquifers, the rock mass and fractures are often simulated as being two overlapping but distinct bodies. Delayed yield, and leaky aquifer flow solutions are both mathematically similar solutions to that obtained for dual porosity; in all three cases water comes from two mathematically different reservoirs (whether or not they are physically different).

Macro porosity

Refers to pores greater than 50 nm in diameter. Flow through macropores is described by bulk diffusion.

Meso porosity

Refers to pores greater than 2 nm and less than 50 nm in diameter. Flow through mesopores is described by Knudsen diffusion.

Micro porosity

Refers to pores smaller than 2 nm in diameter. Movement in micropores is by activated diffusion.

Measuring porosity

Optical method of measuring porosity: thin section under gypsum plate shows porosity as purple color, contrasted with carbonate grains of other colors. Pleistocene eolianite from San Salvador Island, Bahamas. Scale bar 500 microns.

Several methods can be employed to measure porosity:

• Direct methods (determining the bulk volume of the porous sample, and then determining the volume of the skeletal material with no pores (pore volume = total volume − material volume).
• Optical methods (e.g., determining the area of the material versus the area of the pores visible under the microscope). The "areal" and "volumetric" porosities are equal for porous media with random structure.
• Computed tomography method (using industrial CT scanning to create a 3D rendering of external and internal geometry, including voids. Then implementing a defect analysis utilizing computer software)
• Imbibition methods, i.e., immersion of the porous sample, under vacuum, in a fluid that preferentially wets the pores.
  • Water saturation method (pore volume = total volume of water − volume of water left after soaking).
• Water evaporation method (pore volume = (weight of saturated sample − weight of dried sample)/density of water)
• Mercury intrusion porosimetry (several non-mercury intrusion techniques have been developed due to toxicological concerns, and the fact that mercury tends to form amalgams with several metals and alloys).

• Gas expansion method. A sample of known bulk volume is enclosed in a container of known volume. It is connected to another container with a known volume which is evacuated (i.e., near vacuum pressure). When a valve connecting the two containers is opened, gas passes from the first container to the second until a uniform pressure distribution is attained. Using ideal gas law, the volume of the pores is calculated as

$V_{V}=V_{T}-V_{a}-V_{b}{P_{2} \over {P_{2}-P_{1}}}$,

where

V_V is the effective volume of the pores,

V_T is the bulk volume of the sample,

V_a is the volume of the container containing the sample,

V_b is the volume of the evacuated container,

P₁ is the initial pressure in the initial pressure in volume V_a and V_V, and

P₂ is final pressure present in the entire system.

The porosity follows straightforwardly by its proper definition

$\phi ={\frac {V_{V}}{V_{T}}}$.

Note that this method assumes that gas communicates between the pores and the surrounding volume. In practice, this means that the pores must not be closed cavities.

• Thermoporosimetry and cryoporometry. A small crystal of a liquid melts at a lower temperature than the bulk liquid, as given by the Gibbs-Thomson equation. Thus if a liquid is imbibed into a porous material, and frozen, the melting temperature will provide information on the pore-size distribution. The detection of the melting can be done by sensing the transient heat flows during phase-changes using differential scanning calorimetry - (DSC thermoporometry), measuring the quantity of mobile liquid using nuclear magnetic resonance - (NMR cryoporometry) or measuring the amplitude of neutron scattering from the imbibed crystalline or liquid phases - (ND cryoporometry).

See also

• Void ratio
• Petroleum geology
• Poromechanics
• Bulk density
• Particle density

References

• Glasbey, C. A. (1991). "Image analysis and three-dimensional modelling of pores in soil aggregates". Journal of Soil Science. 42 (3): 479–486. doi:10.1111/j.1365-2389.1991.tb00424.x. {{cite journal}}: Unknown parameter |coauthors= ignored (|author= suggested) (help); Unknown parameter |month= ignored (help)
• Horgan, G. W. (1994). "Simulating diffusion in a Boolean model of soil pores". European Journal of Soil Science. 45 (4): 483–491. doi:10.1111/j.1365-2389.1994.tb00534.x. {{cite journal}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
• Horgan, Graham W. (1996-10-01). "A review of soil pore models" (PDF). Retrieved 2006-04-16. {{cite journal}}: Cite journal requires |journal= (help)
• Horgan, G. W. (1998). "Mathematical morphology for soil image analysis". European Journal of Soil Science. 49 (2): 161–173. doi:10.1046/j.1365-2389.1998.00160.x. {{cite journal}}: Unknown parameter |month= ignored (help)
• Horgan, G. W. (1999). "An investigation of the geometric influences on pore space diffusion". Geoderma. 88 (1–2): 55–71. doi:10.1016/S0016-7061(98)00075-5. {{cite journal}}: Unknown parameter |month= ignored (help)
• Nelson, J. Roy (2000). "Physics of impregnation" (PDF). Microscopy Today. 8 (1). {{cite journal}}: Unknown parameter |month= ignored (help)