There are often bonding problems between acrylic resins and silicone. PEEK (polyetheretherketone)... more There are often bonding problems between acrylic resins and silicone. PEEK (polyetheretherketone), which is a high-performance polymer, has great potential for the implant, and fixed or removable prosthodontics. The aim of this study was to evaluate the effect of different surface treatments on PEEK to be bonded to maxillofacial silicone elastomers. A total of 48 specimens were fabricated from either PEEK or PMMA (Polymethylmethacrylate) (n = 8). PMMA specimens acted as a positive control group. PEEK specimens were divided into five study groups as surface treatments as control PEEK, silica-coating, plasma etching, grinding, or nano-second fiber laser. Surface topographies were evaluated by scanning electron microscopy (SEM). A platinum-primer was used on top of all specimens including control groups prior to silicone polymerization. The peel bond strength of the specimens to a platinum-type silicone elastomer was tested at a cross-head speed of 5 mm/min. The data were statistically...
Nature Publishing, Reactive and Functional Polymers Volume One, 2020
Biobased polymers are of great interest due to the release of tension on non-renewable petroleum-... more Biobased polymers are of great interest due to the release of tension on non-renewable petroleum-based polymers for environmental concerns. However, biobased polymers usually have poor mechanical and barrier properties when used as the main component of coatings and films, but they can be improved by adding nanoscale reinforcing agents (nanoparticles - NPs or fillers), thus forming nanocomposites. The nano-sized components have a larger surface area that favors the filler-matrix interactions and the resulting material yield. For example, natural fibers from renewable plants could be used to improve the mechanical strength of the biobased composites. In addition to the mechanical properties, the optical, thermal and barrier properties are mainly effective on the selection of type or the ratio of biobased components. Biobased nanocomposites are one of the best alternatives to conventional polymer composites due to their low density, transparency, better surface properties and biodegra...
Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of f... more Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of four current adhesive materials that contain different monomers at deep and superficial dentin. Material and Methods: Forty non-carious human third molars (n = 5) were used in the study. Specimens were divided into two main groups according to dentin thickness as superficial and deep dentin. Groups were further divided into four subgroups in terms of the adhesive systems used: Nova Compo B Plus (NCBP), Nova Compo B (NCB), Futurabond M (FB) and Clearfil S3 Bond Plus (CS3). All specimens were bonded to resin composite and stored in 37 °C water for 9-months. Teeth were sectioned into 3 x 3 mm x 1mm thick beams. Microtensile bond strength test was carried out by using a universal testing device (1 mm/min). After fracture, failure types were observed using an optical microscope and the fractured dentin surfaces were observed by a scanning electron microscopy (SEM). One-way ANOVA and Tukey test...
Abstract Aim: The aim of this study was to evaluate the effect of various surface treatments on t... more Abstract Aim: The aim of this study was to evaluate the effect of various surface treatments on the bond strength of veneering feldspathic porcelain to zirconia. Methods: Fifty yttria-stabilized tetragonal zirconia polycrystalline specimens were divided into five groups (n = 10) according to various surface treatments. The groups were as follows: Group 1: control group with liner application and no further surface treatment; Group 2: air-particle abrasion with 110 μm of alumina (Al2O3) particles; Group 3: grinding with a diamond disk; Group 4: Nd:YAG laser irradiation (the laser and the energy parameters were 10 Hz, and 2 W and 200 mJ, and the pulse duration (short pulse) range was up to 180 μs); Group 5: selective infiltration etching (SIE). After surface treatments, a liner application was performed for all surfaces according to the manufacturer’s instructions. Veneering porcelain was applied on zirconia surfaces using a Teflon mold. Shear bond strength was tested using a universal testing machine. The fractured surface morphologies were examined with scanning electron microscopy. The data were statistically analyzed using Mann–Whitney U and Kruskal–Wallis tests (α = .05). Results: The Megapascal values of the bonding groups were as follows: G1 = 8.62 ± 1.12, G2 = 13.87 ± 5.08, G3 = 12.31 ± 3.35, G4 = 17.32 ± 6.16, and G5 = 16.17 ± 4.55. Statistically significant differences were observed between the control group and the other groups (p < 0.05). Group 4 had the highest bond strength while G1 showed the lowest bond strength. No significant differences were found between the Nd:YAG, grinding, sandblasting, and SIE groups. Conclusion: Surface treatments had different effects on the shear bond strength of feldspathic porcelain to zirconia. Surface treatment techniques used in this study can be used on zirconia specimens prior to liner application to obtain an acceptable bond strength of veneering porcelain to zirconia. The effect of Nd:YAG laser irradiation and SIE techniques on bond strength of veneering ceramic to zirconia should be evaluated with further studies.
Journal of prosthodontics : official journal of the American College of Prosthodontists, Jan 4, 2016
Silicone-based elastomeric materials are commonly used to fabricate maxillofacial prostheses. The... more Silicone-based elastomeric materials are commonly used to fabricate maxillofacial prostheses. The aim of this study was to evaluate the effect of different types of silica and nanosized titanium dioxide addition on the mechanical properties of two RTV silicone elastomers. A-2000 and A-2006 silicone elastomers were used, and each was divided into four subgroups (n = 5). The first group was the control without additives. Other groups were titanium dioxide, fumed silica, and silaned silica. Each specimen was prepared in compliance with the manufacturer's instructions for the tensile strength, percent elongation, tear resistance, and the hardness tests according to ISO and ASTM standards. A factorial ANOVA with pairwise interaction indicated that the pattern for all four outcomes of the materials was different for A-2000 and A-2006 (p < 0.05). Therefore, the average outcome values for the materials within silicone elastomers were then analyzed by Tukey HSD. For the hardness test ...
Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi, 2016
This clinical case describes rehabilitation of the a young patient's anterior teeth via modified ... more This clinical case describes rehabilitation of the a young patient's anterior teeth via modified laminate veneer restorations with all-ceramic one-piece coronal post technique, crown, and 3-unit fixed dental prosthesis. The modified laminate veneer procedure mentioned in this case report represents an alternative to traditional complete crown restorations via adhesive systems and can yield satisfactory esthetic and functional results.
Innovations in digital manufacturing enabled the fabrication of implant-supported fixed dental pr... more Innovations in digital manufacturing enabled the fabrication of implant-supported fixed dental prostheses (ISFDPs) in a wide variety of recently introduced materials. Computer-aided design and computer-aided manufacturing (CAD-CAM) milling allows the fabrication of ISFDPs with high accuracy by reducing the fabrication steps of large-span frameworks. The longevity of ISFDPs depends on the overall mechanical properties of the framework material including its fit, and the physical properties of the veneering material and its bond with the framework. This comprehensive review summarizes the recent information on millable CAD-CAM framework materials such as pre-sintered soft alloys, fiber-reinforced composite resins, PEEK, and PEKK in high-performance polymer family, and 4Y-TZP. Even though promising results have been obtained with the use of new generation millable CAD-CAM materials for ISFDPs, clinical studies are lacking and future research should focus on the overall performance of t...
STATEMENT OF PROBLEM The separation of a denture liner from the denture base can be a clinical pr... more STATEMENT OF PROBLEM The separation of a denture liner from the denture base can be a clinical problem. Different surface treatments to increase the bond have been evaluated, but studies comparing the effect of argon plasma and erbium-doped yttrium aluminum garnet (Er:YAG) laser on the bond between acrylic resin and a denture liner are lacking. PURPOSE The purpose of this in vitro study was to evaluate the effect of argon plasma and Er:YAG laser treatments on the bond strengths of acrylic resin to 2 denture liners. MATERIALS AND METHODS Heat-polymerized acrylic resin (Acron Duo) was bonded to silicone soft-liner materials (Molloplast B, n=30; Mollosil, n=30) to create control specimens (n=10), argon plasma treatment (n=10), and Er:YAG laser treatment (n=10). Silicone liners were polymerized on resin specimens. The tensile bond strength test was performed with a crosshead speed of 10 mm/min with a 10-N load until failure. Data were analyzed by using the Kruskal-Wallis test and unpair...
Maxillofacial prostheses are used for patients with deformities in the maxillofacial area induced... more Maxillofacial prostheses are used for patients with deformities in the maxillofacial area induced by cancer, trauma or congenital defects. Different types of polymers are used in the manufacture of maxillofacial prosthesis. However, silicone elastomers are the polymers most commonly used in the maxillofacial prosthodontics because of their acceptable properties. Since maxillofacial defects create profound psychological and social difficulties in these patients, recent research focused on improving the mechanical and physical properties of silicone elastomers by using various incorporations of nano-oxide particles into the silicones. Nevertheless, the use of conventional techniques in the manufacture of maxillofacial silicones still consumes a lot of time. Silicone prostheses manufactured conventionally are also still susceptible to color degradation and change in the mechanical properties. Thus, the three-dimensional (3D) printing techniques of the maxillofacial prosthesis and the d...
Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of f... more Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of four current adhesive materials that contain different monomers at deep and superficial dentin. Material and Methods: Forty non-carious human third molars (n=5) were used in the study. Specimens were divided into two main groups according to dentin thickness as superficial and deep dentin. Groups were further divided into four subgroups in terms of the adhesive systems used: Nova Compo B Plus (NCBP), Nova Compo B (NCB), Futurabond M (FB) and Clearfil S3 Bond Plus (CS3). All specimens were bonded to resin composite and stored in 37 °C water for 9-months. Teeth were sectioned into 3 x 3 mm thick beams. Microtensile bond strength test was carried out by using a universal testing device (1 mm/min). After fracture, failure types were observed using an optical microscope and the fractured dentin surfaces were observed by a scanning electron microscopy (SEM). One-way ANOVA and Tukey tests were used to compare the adhesive system in each dentin group. An unpaired T-test was used to compare the dentin thickness in each adhesive material. Results: As compared to deep dentin, superficial dentin showed higher µTBS values in groups NCBP, FB and CS, as opposed to group NCB. Only NCB revealed higher bond strength at deep dentin layers when compared to superficial dentin. In the superficial dentin group, NCBP showed the highest bond strength value, RESUMO Objetivo: o objetivo deste estudo foi avaliar e comparar a resistência de união à microtração de quatro materiais adesivos atuais que contêm monômeros diferentes na dentina profunda e superficial. Material e Métodos: Quarenta terceiros molares humanos não cariados (n = 5) foram usados no estudo. Os espécimes foram divididos em dois grupos principais de acordo com a espessura da dentina em superficial e profunda. Os grupos foram subdivididos em quatro subgrupos quanto aos sistemas adesivos usados: Nova Compo B Plus (NCBP), Nova Compo B (NCB), Futurabond M (FB) e Clearfil S3 Bond Plus (CS3). Todos os espécimes foram aderidos à resina composta e armazenados em água a 37 ° C por 9 meses. Os dentes foram seccionados em palitos de 3 x 3 mm de espessura. O teste de microtração foi realizado com o uso de um dispositivo de teste universal (1 mm / min). Após a fratura, os tipos de falha foram observados em microscópio óptico e as superfícies de dentina fraturadas por microscopia eletrônica de varredura (MEV). Os testes ANOVA e Tukey um fator foram usados para comparar o sistema adesivo em cada grupo de dentina. Um teste T não pareado foi usado para comparar a espessura da dentina em cada material adesivo. Resultados: Em comparação com a dentina profunda, a dentina superficial apresentou maiores valores de µTBS nos grupos NCBP, FB e CS, ao contrário do grupo NCB. Apenas NCB revelou maior resistência de união na dentina profunda quando comparada à dentina superficial. No grupo de dentina superficial, NCBP apresentou o maior valor de resistência de união, enquanto NCB apresentou a menor
Purpose: Patients with maxillofacial deformities always seek for aesthetic prosthesis. Recently, ... more Purpose: Patients with maxillofacial deformities always seek for aesthetic prosthesis. Recently, three-dimensional printing technologies have been used for dental treatments on such patients. Case report: A 24-year-old man reported to the Department of Prosthodontics for replacement of his missing right ear induced by a trauma. A magnet-retained auricular prosthesis was planned for the patient. Three-dimensional scanning was performed on the healthy side by using a three-dimensional optical scanner and the data were mirrored. The mirrored image was then imported to a software and a virtual model of the future prosthesis was obtained for the defect side. A three-dimensional printer was used to fabricate a negative mold for the mirrored image by using additive manufacturing. Initially, an impression of the defect side was made; then, the cast model was obtained in a dental flask. Magnets of the prosthesis were inserted to the acrylic resin framework on the cast model. Room temperature...
The International journal of artificial organs, Jan 9, 2017
Understanding the effect of aging and different disinfecting agents on the physical properties of... more Understanding the effect of aging and different disinfecting agents on the physical properties of pigmented maxillofacial silicones may help eliminate the current uncertainty as to the best follow-up suggestions for the patients treated with silicone prostheses. One hundred fifty specimens (14 × 2 mm) were evaluated for colour and 75 specimens (30 × 10 mm) for hardness (total, 225 specimens). Five specimens were used for hardness testing in each disinfecting solution while 10 silicone specimens were used for colour evaluation. The samples were separated into 5 groups and the initial hardness and colour evaluations were performed and placed in disinfectant solution (neutral soap, effervescent tablet, 0.2% chlorhexidine, 4% chlorhexidine, sodium hypochlorite). A second set of colour and hardness measurements was taken after 48 hours of disinfection and 1,008 hours of artificial aging in a QUV-accelerated weathering tester. Two-way and 1-way analysis of variance with Tukey tests and pa...
The International journal of artificial organs, 2018
The aim of this study was to evaluate the effect of six different surface conditioning methods on... more The aim of this study was to evaluate the effect of six different surface conditioning methods on the shear bond strength of ceramic brackets bonded to feldspathic porcelain. A total of 60 feldspathic porcelain disks were fabricated and divided into six subgroups including 10 specimens in each. Specimens were first treated one of the following surface conditioning methods, namely, 37% phosphoric acid (G-H3PO4), 9.4% hydrofluoric acid (G-HF), grinding with diamond burs (G-Grinding), Nd:YAG laser (G-Nd:YAG), Airborne-particle abrasion (G-Abrasion). Specimens were also coated with silane without surface treatment for comparison (G-Untreated). A total of 60 ceramic brackets were bonded to porcelain surfaces with a composite resin and then subjected to thermocycling 2500× between 5°C and 55°C. The shear bond strength test was carried out using a universal testing device at a crosshead speed of 0.5 mm/min. Failure types were classified according to the adhesive remnant index. Analysis of ...
Amac: Bu calismanin amaci, zirkonya yuzeyine uygulanan farkli yuzey islemlerinin yaslandirma sonr... more Amac: Bu calismanin amaci, zirkonya yuzeyine uygulanan farkli yuzey islemlerinin yaslandirma sonrasi kompozit rezin ve zirkonya arasindaki makaslama baglanma dayanimina etkisini incelemektir. Gerec ve Yontemler: 40 adet sinterlenmis zirkonya ornek (19x15x2 mm) dort farkli yuzey islemi grubuna ayrildi (n=10): Grup 1, elmas frez ile asindirma; Grup 2, 30 μm Al2O3 ile tribokimyasal silika kaplama; Grup 3, 50 μm Al2O3 ile kumlama ve Grup 4, 110 μm Al2O3 ile kumlama grubu. Yuzey islemi goren zirkonya orneklere adeziv fosfat monomeri uygulanip polimerize edildi. Kompozit rezin polimerizasyonunu takiben ornekler termal yaslandirmaya (x1000, 5-55 °C, 30 saniye) tabi tutuldu. Orneklere hizi 0.5 mm/dakika olan universal test cihazi ile makaslama baglanma dayanimi testi uygulandi. Test sonrasi kirilma tipleri adeziv veya karma tip basarisizlik olarak kaydedildi. Istatistiksel analiz tek yonlu varyans analizi (ANOVA) ve Tukey HSD testleri kullanilarak yapildi (p 0.05). Tum gruplarda adeziv tip basarisizlik gozlenmistir. Sonuc: Tum gruplar klinik olarak kabul edilebilir baglanma dayanimi degerleri gostermistir. Bununla birlikte tribokimyasal silika kaplama yonteminin zirkonya ile kompozit rezin arasindaki baglanma dayanimini anlamli derecede artirdigi gozlenmistir.
There are often bonding problems between acrylic resins and silicone. PEEK (polyetheretherketone)... more There are often bonding problems between acrylic resins and silicone. PEEK (polyetheretherketone), which is a high-performance polymer, has great potential for the implant, and fixed or removable prosthodontics. The aim of this study was to evaluate the effect of different surface treatments on PEEK to be bonded to maxillofacial silicone elastomers. A total of 48 specimens were fabricated from either PEEK or PMMA (Polymethylmethacrylate) (n = 8). PMMA specimens acted as a positive control group. PEEK specimens were divided into five study groups as surface treatments as control PEEK, silica-coating, plasma etching, grinding, or nano-second fiber laser. Surface topographies were evaluated by scanning electron microscopy (SEM). A platinum-primer was used on top of all specimens including control groups prior to silicone polymerization. The peel bond strength of the specimens to a platinum-type silicone elastomer was tested at a cross-head speed of 5 mm/min. The data were statistically...
Nature Publishing, Reactive and Functional Polymers Volume One, 2020
Biobased polymers are of great interest due to the release of tension on non-renewable petroleum-... more Biobased polymers are of great interest due to the release of tension on non-renewable petroleum-based polymers for environmental concerns. However, biobased polymers usually have poor mechanical and barrier properties when used as the main component of coatings and films, but they can be improved by adding nanoscale reinforcing agents (nanoparticles - NPs or fillers), thus forming nanocomposites. The nano-sized components have a larger surface area that favors the filler-matrix interactions and the resulting material yield. For example, natural fibers from renewable plants could be used to improve the mechanical strength of the biobased composites. In addition to the mechanical properties, the optical, thermal and barrier properties are mainly effective on the selection of type or the ratio of biobased components. Biobased nanocomposites are one of the best alternatives to conventional polymer composites due to their low density, transparency, better surface properties and biodegra...
Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of f... more Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of four current adhesive materials that contain different monomers at deep and superficial dentin. Material and Methods: Forty non-carious human third molars (n = 5) were used in the study. Specimens were divided into two main groups according to dentin thickness as superficial and deep dentin. Groups were further divided into four subgroups in terms of the adhesive systems used: Nova Compo B Plus (NCBP), Nova Compo B (NCB), Futurabond M (FB) and Clearfil S3 Bond Plus (CS3). All specimens were bonded to resin composite and stored in 37 °C water for 9-months. Teeth were sectioned into 3 x 3 mm x 1mm thick beams. Microtensile bond strength test was carried out by using a universal testing device (1 mm/min). After fracture, failure types were observed using an optical microscope and the fractured dentin surfaces were observed by a scanning electron microscopy (SEM). One-way ANOVA and Tukey test...
Abstract Aim: The aim of this study was to evaluate the effect of various surface treatments on t... more Abstract Aim: The aim of this study was to evaluate the effect of various surface treatments on the bond strength of veneering feldspathic porcelain to zirconia. Methods: Fifty yttria-stabilized tetragonal zirconia polycrystalline specimens were divided into five groups (n = 10) according to various surface treatments. The groups were as follows: Group 1: control group with liner application and no further surface treatment; Group 2: air-particle abrasion with 110 μm of alumina (Al2O3) particles; Group 3: grinding with a diamond disk; Group 4: Nd:YAG laser irradiation (the laser and the energy parameters were 10 Hz, and 2 W and 200 mJ, and the pulse duration (short pulse) range was up to 180 μs); Group 5: selective infiltration etching (SIE). After surface treatments, a liner application was performed for all surfaces according to the manufacturer’s instructions. Veneering porcelain was applied on zirconia surfaces using a Teflon mold. Shear bond strength was tested using a universal testing machine. The fractured surface morphologies were examined with scanning electron microscopy. The data were statistically analyzed using Mann–Whitney U and Kruskal–Wallis tests (α = .05). Results: The Megapascal values of the bonding groups were as follows: G1 = 8.62 ± 1.12, G2 = 13.87 ± 5.08, G3 = 12.31 ± 3.35, G4 = 17.32 ± 6.16, and G5 = 16.17 ± 4.55. Statistically significant differences were observed between the control group and the other groups (p < 0.05). Group 4 had the highest bond strength while G1 showed the lowest bond strength. No significant differences were found between the Nd:YAG, grinding, sandblasting, and SIE groups. Conclusion: Surface treatments had different effects on the shear bond strength of feldspathic porcelain to zirconia. Surface treatment techniques used in this study can be used on zirconia specimens prior to liner application to obtain an acceptable bond strength of veneering porcelain to zirconia. The effect of Nd:YAG laser irradiation and SIE techniques on bond strength of veneering ceramic to zirconia should be evaluated with further studies.
Journal of prosthodontics : official journal of the American College of Prosthodontists, Jan 4, 2016
Silicone-based elastomeric materials are commonly used to fabricate maxillofacial prostheses. The... more Silicone-based elastomeric materials are commonly used to fabricate maxillofacial prostheses. The aim of this study was to evaluate the effect of different types of silica and nanosized titanium dioxide addition on the mechanical properties of two RTV silicone elastomers. A-2000 and A-2006 silicone elastomers were used, and each was divided into four subgroups (n = 5). The first group was the control without additives. Other groups were titanium dioxide, fumed silica, and silaned silica. Each specimen was prepared in compliance with the manufacturer's instructions for the tensile strength, percent elongation, tear resistance, and the hardness tests according to ISO and ASTM standards. A factorial ANOVA with pairwise interaction indicated that the pattern for all four outcomes of the materials was different for A-2000 and A-2006 (p < 0.05). Therefore, the average outcome values for the materials within silicone elastomers were then analyzed by Tukey HSD. For the hardness test ...
Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi, 2016
This clinical case describes rehabilitation of the a young patient's anterior teeth via modified ... more This clinical case describes rehabilitation of the a young patient's anterior teeth via modified laminate veneer restorations with all-ceramic one-piece coronal post technique, crown, and 3-unit fixed dental prosthesis. The modified laminate veneer procedure mentioned in this case report represents an alternative to traditional complete crown restorations via adhesive systems and can yield satisfactory esthetic and functional results.
Innovations in digital manufacturing enabled the fabrication of implant-supported fixed dental pr... more Innovations in digital manufacturing enabled the fabrication of implant-supported fixed dental prostheses (ISFDPs) in a wide variety of recently introduced materials. Computer-aided design and computer-aided manufacturing (CAD-CAM) milling allows the fabrication of ISFDPs with high accuracy by reducing the fabrication steps of large-span frameworks. The longevity of ISFDPs depends on the overall mechanical properties of the framework material including its fit, and the physical properties of the veneering material and its bond with the framework. This comprehensive review summarizes the recent information on millable CAD-CAM framework materials such as pre-sintered soft alloys, fiber-reinforced composite resins, PEEK, and PEKK in high-performance polymer family, and 4Y-TZP. Even though promising results have been obtained with the use of new generation millable CAD-CAM materials for ISFDPs, clinical studies are lacking and future research should focus on the overall performance of t...
STATEMENT OF PROBLEM The separation of a denture liner from the denture base can be a clinical pr... more STATEMENT OF PROBLEM The separation of a denture liner from the denture base can be a clinical problem. Different surface treatments to increase the bond have been evaluated, but studies comparing the effect of argon plasma and erbium-doped yttrium aluminum garnet (Er:YAG) laser on the bond between acrylic resin and a denture liner are lacking. PURPOSE The purpose of this in vitro study was to evaluate the effect of argon plasma and Er:YAG laser treatments on the bond strengths of acrylic resin to 2 denture liners. MATERIALS AND METHODS Heat-polymerized acrylic resin (Acron Duo) was bonded to silicone soft-liner materials (Molloplast B, n=30; Mollosil, n=30) to create control specimens (n=10), argon plasma treatment (n=10), and Er:YAG laser treatment (n=10). Silicone liners were polymerized on resin specimens. The tensile bond strength test was performed with a crosshead speed of 10 mm/min with a 10-N load until failure. Data were analyzed by using the Kruskal-Wallis test and unpair...
Maxillofacial prostheses are used for patients with deformities in the maxillofacial area induced... more Maxillofacial prostheses are used for patients with deformities in the maxillofacial area induced by cancer, trauma or congenital defects. Different types of polymers are used in the manufacture of maxillofacial prosthesis. However, silicone elastomers are the polymers most commonly used in the maxillofacial prosthodontics because of their acceptable properties. Since maxillofacial defects create profound psychological and social difficulties in these patients, recent research focused on improving the mechanical and physical properties of silicone elastomers by using various incorporations of nano-oxide particles into the silicones. Nevertheless, the use of conventional techniques in the manufacture of maxillofacial silicones still consumes a lot of time. Silicone prostheses manufactured conventionally are also still susceptible to color degradation and change in the mechanical properties. Thus, the three-dimensional (3D) printing techniques of the maxillofacial prosthesis and the d...
Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of f... more Objective: The aim of this study was to evaluate and compare the microtensile bond strengths of four current adhesive materials that contain different monomers at deep and superficial dentin. Material and Methods: Forty non-carious human third molars (n=5) were used in the study. Specimens were divided into two main groups according to dentin thickness as superficial and deep dentin. Groups were further divided into four subgroups in terms of the adhesive systems used: Nova Compo B Plus (NCBP), Nova Compo B (NCB), Futurabond M (FB) and Clearfil S3 Bond Plus (CS3). All specimens were bonded to resin composite and stored in 37 °C water for 9-months. Teeth were sectioned into 3 x 3 mm thick beams. Microtensile bond strength test was carried out by using a universal testing device (1 mm/min). After fracture, failure types were observed using an optical microscope and the fractured dentin surfaces were observed by a scanning electron microscopy (SEM). One-way ANOVA and Tukey tests were used to compare the adhesive system in each dentin group. An unpaired T-test was used to compare the dentin thickness in each adhesive material. Results: As compared to deep dentin, superficial dentin showed higher µTBS values in groups NCBP, FB and CS, as opposed to group NCB. Only NCB revealed higher bond strength at deep dentin layers when compared to superficial dentin. In the superficial dentin group, NCBP showed the highest bond strength value, RESUMO Objetivo: o objetivo deste estudo foi avaliar e comparar a resistência de união à microtração de quatro materiais adesivos atuais que contêm monômeros diferentes na dentina profunda e superficial. Material e Métodos: Quarenta terceiros molares humanos não cariados (n = 5) foram usados no estudo. Os espécimes foram divididos em dois grupos principais de acordo com a espessura da dentina em superficial e profunda. Os grupos foram subdivididos em quatro subgrupos quanto aos sistemas adesivos usados: Nova Compo B Plus (NCBP), Nova Compo B (NCB), Futurabond M (FB) e Clearfil S3 Bond Plus (CS3). Todos os espécimes foram aderidos à resina composta e armazenados em água a 37 ° C por 9 meses. Os dentes foram seccionados em palitos de 3 x 3 mm de espessura. O teste de microtração foi realizado com o uso de um dispositivo de teste universal (1 mm / min). Após a fratura, os tipos de falha foram observados em microscópio óptico e as superfícies de dentina fraturadas por microscopia eletrônica de varredura (MEV). Os testes ANOVA e Tukey um fator foram usados para comparar o sistema adesivo em cada grupo de dentina. Um teste T não pareado foi usado para comparar a espessura da dentina em cada material adesivo. Resultados: Em comparação com a dentina profunda, a dentina superficial apresentou maiores valores de µTBS nos grupos NCBP, FB e CS, ao contrário do grupo NCB. Apenas NCB revelou maior resistência de união na dentina profunda quando comparada à dentina superficial. No grupo de dentina superficial, NCBP apresentou o maior valor de resistência de união, enquanto NCB apresentou a menor
Purpose: Patients with maxillofacial deformities always seek for aesthetic prosthesis. Recently, ... more Purpose: Patients with maxillofacial deformities always seek for aesthetic prosthesis. Recently, three-dimensional printing technologies have been used for dental treatments on such patients. Case report: A 24-year-old man reported to the Department of Prosthodontics for replacement of his missing right ear induced by a trauma. A magnet-retained auricular prosthesis was planned for the patient. Three-dimensional scanning was performed on the healthy side by using a three-dimensional optical scanner and the data were mirrored. The mirrored image was then imported to a software and a virtual model of the future prosthesis was obtained for the defect side. A three-dimensional printer was used to fabricate a negative mold for the mirrored image by using additive manufacturing. Initially, an impression of the defect side was made; then, the cast model was obtained in a dental flask. Magnets of the prosthesis were inserted to the acrylic resin framework on the cast model. Room temperature...
The International journal of artificial organs, Jan 9, 2017
Understanding the effect of aging and different disinfecting agents on the physical properties of... more Understanding the effect of aging and different disinfecting agents on the physical properties of pigmented maxillofacial silicones may help eliminate the current uncertainty as to the best follow-up suggestions for the patients treated with silicone prostheses. One hundred fifty specimens (14 × 2 mm) were evaluated for colour and 75 specimens (30 × 10 mm) for hardness (total, 225 specimens). Five specimens were used for hardness testing in each disinfecting solution while 10 silicone specimens were used for colour evaluation. The samples were separated into 5 groups and the initial hardness and colour evaluations were performed and placed in disinfectant solution (neutral soap, effervescent tablet, 0.2% chlorhexidine, 4% chlorhexidine, sodium hypochlorite). A second set of colour and hardness measurements was taken after 48 hours of disinfection and 1,008 hours of artificial aging in a QUV-accelerated weathering tester. Two-way and 1-way analysis of variance with Tukey tests and pa...
The International journal of artificial organs, 2018
The aim of this study was to evaluate the effect of six different surface conditioning methods on... more The aim of this study was to evaluate the effect of six different surface conditioning methods on the shear bond strength of ceramic brackets bonded to feldspathic porcelain. A total of 60 feldspathic porcelain disks were fabricated and divided into six subgroups including 10 specimens in each. Specimens were first treated one of the following surface conditioning methods, namely, 37% phosphoric acid (G-H3PO4), 9.4% hydrofluoric acid (G-HF), grinding with diamond burs (G-Grinding), Nd:YAG laser (G-Nd:YAG), Airborne-particle abrasion (G-Abrasion). Specimens were also coated with silane without surface treatment for comparison (G-Untreated). A total of 60 ceramic brackets were bonded to porcelain surfaces with a composite resin and then subjected to thermocycling 2500× between 5°C and 55°C. The shear bond strength test was carried out using a universal testing device at a crosshead speed of 0.5 mm/min. Failure types were classified according to the adhesive remnant index. Analysis of ...
Amac: Bu calismanin amaci, zirkonya yuzeyine uygulanan farkli yuzey islemlerinin yaslandirma sonr... more Amac: Bu calismanin amaci, zirkonya yuzeyine uygulanan farkli yuzey islemlerinin yaslandirma sonrasi kompozit rezin ve zirkonya arasindaki makaslama baglanma dayanimina etkisini incelemektir. Gerec ve Yontemler: 40 adet sinterlenmis zirkonya ornek (19x15x2 mm) dort farkli yuzey islemi grubuna ayrildi (n=10): Grup 1, elmas frez ile asindirma; Grup 2, 30 μm Al2O3 ile tribokimyasal silika kaplama; Grup 3, 50 μm Al2O3 ile kumlama ve Grup 4, 110 μm Al2O3 ile kumlama grubu. Yuzey islemi goren zirkonya orneklere adeziv fosfat monomeri uygulanip polimerize edildi. Kompozit rezin polimerizasyonunu takiben ornekler termal yaslandirmaya (x1000, 5-55 °C, 30 saniye) tabi tutuldu. Orneklere hizi 0.5 mm/dakika olan universal test cihazi ile makaslama baglanma dayanimi testi uygulandi. Test sonrasi kirilma tipleri adeziv veya karma tip basarisizlik olarak kaydedildi. Istatistiksel analiz tek yonlu varyans analizi (ANOVA) ve Tukey HSD testleri kullanilarak yapildi (p 0.05). Tum gruplarda adeziv tip basarisizlik gozlenmistir. Sonuc: Tum gruplar klinik olarak kabul edilebilir baglanma dayanimi degerleri gostermistir. Bununla birlikte tribokimyasal silika kaplama yonteminin zirkonya ile kompozit rezin arasindaki baglanma dayanimini anlamli derecede artirdigi gozlenmistir.
Uploads
Papers by pinar cevik