optiboot_atmega8.elf: file format elf32-avr

Sections:

Idx Name Size VMA LMA File off Algn

0 .text 000001e0 00001e00 00001e00 00000054 2**1

CONTENTS, ALLOC, LOAD, READONLY, CODE

1 .version 00000002 00001ffe 00001ffe 00000234 2**0

CONTENTS, READONLY

2 .debug_aranges 00000028 00000000 00000000 00000236 2**0

CONTENTS, READONLY, DEBUGGING

3 .debug_pubnames 0000005f 00000000 00000000 0000025e 2**0

CONTENTS, READONLY, DEBUGGING

4 .debug_info 000002a6 00000000 00000000 000002bd 2**0

CONTENTS, READONLY, DEBUGGING

5 .debug_abbrev 00000169 00000000 00000000 00000563 2**0

CONTENTS, READONLY, DEBUGGING

6 .debug_line 00000498 00000000 00000000 000006cc 2**0

CONTENTS, READONLY, DEBUGGING

7 .debug_frame 00000080 00000000 00000000 00000b64 2**2

CONTENTS, READONLY, DEBUGGING

8 .debug_str 0000014f 00000000 00000000 00000be4 2**0

CONTENTS, READONLY, DEBUGGING

9 .debug_loc 000002ba 00000000 00000000 00000d33 2**0

CONTENTS, READONLY, DEBUGGING

10 .debug_ranges 00000078 00000000 00000000 00000fed 2**0

CONTENTS, READONLY, DEBUGGING

Disassembly of section .text:

00001e00 <main>:

#define rstVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+4))

#define wdtVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+6))

#endif

/* main program starts here */

int main(void) {

1e00: 11 24 eor r1, r1

//

// If not, uncomment the following instructions:

// cli();

asm volatile ("clr __zero_reg__");

#ifdef __AVR_ATmega8__

SP=RAMEND; // This is done by hardware reset

1e02: 8f e5 ldi r24, 0x5F ; 95

1e04: 94 e0 ldi r25, 0x04 ; 4

1e06: 9e bf out 0x3e, r25 ; 62

1e08: 8d bf out 0x3d, r24 ; 61

#endif

// Adaboot no-wait mod

ch = MCUSR;

1e0a: 84 b7 in r24, 0x34 ; 52

MCUSR = 0;

1e0c: 14 be out 0x34, r1 ; 52

if (!(ch & _BV(EXTRF))) appStart();

1e0e: 81 ff sbrs r24, 1

1e10: e2 d0 rcall .+452 ; 0x1fd6 <appStart>

#if LED_START_FLASHES > 0

// Set up Timer 1 for timeout counter

TCCR1B = _BV(CS12) | _BV(CS10); // div 1024

1e12: 85 e0 ldi r24, 0x05 ; 5

1e14: 8e bd out 0x2e, r24 ; 46

#endif

#ifndef SOFT_UART

#ifdef __AVR_ATmega8__

UCSRA = _BV(U2X); //Double speed mode USART

1e16: 82 e0 ldi r24, 0x02 ; 2

1e18: 8b b9 out 0x0b, r24 ; 11

UCSRB = _BV(RXEN) | _BV(TXEN); // enable Rx & Tx

1e1a: 88 e1 ldi r24, 0x18 ; 24

1e1c: 8a b9 out 0x0a, r24 ; 10

UCSRC = _BV(URSEL) | _BV(UCSZ1) | _BV(UCSZ0); // config USART; 8N1

1e1e: 86 e8 ldi r24, 0x86 ; 134

1e20: 80 bd out 0x20, r24 ; 32

UBRRL = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );

1e22: 80 e1 ldi r24, 0x10 ; 16

1e24: 89 b9 out 0x09, r24 ; 9

UBRR0L = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );

#endif

#endif

// Set up watchdog to trigger after 500ms

watchdogConfig(WATCHDOG_1S);

1e26: 8e e0 ldi r24, 0x0E ; 14

1e28: c2 d0 rcall .+388 ; 0x1fae <watchdogConfig>

/* Set LED pin as output */

LED_DDR |= _BV(LED);

1e2a: bd 9a sbi 0x17, 5 ; 23

1e2c: 96 e0 ldi r25, 0x06 ; 6

}

#if LED_START_FLASHES > 0

void flash_led(uint8_t count) {

do {

TCNT1 = -(F_CPU/(1024*16));

1e2e: 20 e3 ldi r18, 0x30 ; 48

1e30: 3c ef ldi r19, 0xFC ; 252

TIFR1 = _BV(TOV1);

1e32: 54 e0 ldi r21, 0x04 ; 4

while(!(TIFR1 & _BV(TOV1)));

#ifdef __AVR_ATmega8__

LED_PORT ^= _BV(LED);

1e34: 40 e2 ldi r20, 0x20 ; 32

}

#if LED_START_FLASHES > 0

void flash_led(uint8_t count) {

do {

TCNT1 = -(F_CPU/(1024*16));

1e36: 3d bd out 0x2d, r19 ; 45

1e38: 2c bd out 0x2c, r18 ; 44

TIFR1 = _BV(TOV1);

1e3a: 58 bf out 0x38, r21 ; 56

while(!(TIFR1 & _BV(TOV1)));

1e3c: 08 b6 in r0, 0x38 ; 56

1e3e: 02 fe sbrs r0, 2

1e40: fd cf rjmp .-6 ; 0x1e3c <main+0x3c>

#ifdef __AVR_ATmega8__

LED_PORT ^= _BV(LED);

1e42: 88 b3 in r24, 0x18 ; 24

1e44: 84 27 eor r24, r20

1e46: 88 bb out 0x18, r24 ; 24

}

#endif

// Watchdog functions. These are only safe with interrupts turned off.

void watchdogReset() {

__asm__ __volatile__ (

1e48: a8 95 wdr

LED_PORT ^= _BV(LED);

#else

LED_PIN |= _BV(LED);

#endif

watchdogReset();

} while (--count);

1e4a: 91 50 subi r25, 0x01 ; 1

1e4c: a1 f7 brne .-24 ; 0x1e36 <main+0x36>

1e4e: cc 24 eor r12, r12

1e50: dd 24 eor r13, r13

ch = SPM_PAGESIZE / 2;

do {

uint16_t a;

a = *bufPtr++;

a |= (*bufPtr++) << 8;

__boot_page_fill_short((uint16_t)(void*)addrPtr,a);

1e52: 88 24 eor r8, r8

1e54: 83 94 inc r8

addrPtr += 2;

} while (--ch);

// Write from programming buffer

__boot_page_write_short((uint16_t)(void*)address);

1e56: b5 e0 ldi r27, 0x05 ; 5

1e58: ab 2e mov r10, r27

boot_spm_busy_wait();

#if defined(RWWSRE)

// Reenable read access to flash

boot_rww_enable();

1e5a: a1 e1 ldi r26, 0x11 ; 17

1e5c: 9a 2e mov r9, r26

do *bufPtr++ = getch();

while (--length);

// If we are in NRWW section, page erase has to be delayed until now.

// Todo: Take RAMPZ into account

if (address >= NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);

1e5e: f3 e0 ldi r31, 0x03 ; 3

1e60: bf 2e mov r11, r31

#endif

/* Forever loop */

for (;;) {

/* get character from UART */

ch = getch();

1e62: 9e d0 rcall .+316 ; 0x1fa0 <getch>

if(ch == STK_GET_PARAMETER) {

1e64: 81 34 cpi r24, 0x41 ; 65

1e66: 61 f4 brne .+24 ; 0x1e80 <main+0x80>

unsigned char which = getch();

1e68: 9b d0 rcall .+310 ; 0x1fa0 <getch>

1e6a: 08 2f mov r16, r24

verifySpace();

1e6c: a4 d0 rcall .+328 ; 0x1fb6 <verifySpace>

if (which == 0x82) {

1e6e: 02 38 cpi r16, 0x82 ; 130

1e70: 11 f0 breq .+4 ; 0x1e76 <main+0x76>

/*

* Send optiboot version as "minor SW version"

*/

putch(OPTIBOOT_MINVER);

} else if (which == 0x81) {

1e72: 01 38 cpi r16, 0x81 ; 129

1e74: 11 f4 brne .+4 ; 0x1e7a <main+0x7a>

putch(OPTIBOOT_MAJVER);

1e76: 84 e0 ldi r24, 0x04 ; 4

1e78: 01 c0 rjmp .+2 ; 0x1e7c <main+0x7c>

} else {

/*

* GET PARAMETER returns a generic 0x03 reply for

* other parameters - enough to keep Avrdude happy

*/

putch(0x03);

1e7a: 83 e0 ldi r24, 0x03 ; 3

1e7c: 8d d0 rcall .+282 ; 0x1f98 <putch>

1e7e: 89 c0 rjmp .+274 ; 0x1f92 <main+0x192>

}

}

else if(ch == STK_SET_DEVICE) {

1e80: 82 34 cpi r24, 0x42 ; 66

1e82: 11 f4 brne .+4 ; 0x1e88 <main+0x88>

// SET DEVICE is ignored

getNch(20);

1e84: 84 e1 ldi r24, 0x14 ; 20

1e86: 03 c0 rjmp .+6 ; 0x1e8e <main+0x8e>

}

else if(ch == STK_SET_DEVICE_EXT) {

1e88: 85 34 cpi r24, 0x45 ; 69

1e8a: 19 f4 brne .+6 ; 0x1e92 <main+0x92>

// SET DEVICE EXT is ignored

getNch(5);

1e8c: 85 e0 ldi r24, 0x05 ; 5

1e8e: 9b d0 rcall .+310 ; 0x1fc6 <getNch>

1e90: 80 c0 rjmp .+256 ; 0x1f92 <main+0x192>

}

else if(ch == STK_LOAD_ADDRESS) {

1e92: 85 35 cpi r24, 0x55 ; 85

1e94: 79 f4 brne .+30 ; 0x1eb4 <main+0xb4>

// LOAD ADDRESS

uint16_t newAddress;

newAddress = getch();

1e96: 84 d0 rcall .+264 ; 0x1fa0 <getch>

newAddress = (newAddress & 0xff) | (getch() << 8);

1e98: e8 2e mov r14, r24

1e9a: ff 24 eor r15, r15

1e9c: 81 d0 rcall .+258 ; 0x1fa0 <getch>

1e9e: 08 2f mov r16, r24

1ea0: 10 e0 ldi r17, 0x00 ; 0

1ea2: 10 2f mov r17, r16

1ea4: 00 27 eor r16, r16

1ea6: 0e 29 or r16, r14

1ea8: 1f 29 or r17, r15

#ifdef RAMPZ

// Transfer top bit to RAMPZ

RAMPZ = (newAddress & 0x8000) ? 1 : 0;

#endif

newAddress += newAddress; // Convert from word address to byte address

1eaa: 00 0f add r16, r16

1eac: 11 1f adc r17, r17

address = newAddress;

verifySpace();

1eae: 83 d0 rcall .+262 ; 0x1fb6 <verifySpace>

1eb0: 68 01 movw r12, r16

1eb2: 6f c0 rjmp .+222 ; 0x1f92 <main+0x192>

}

else if(ch == STK_UNIVERSAL) {

1eb4: 86 35 cpi r24, 0x56 ; 86

1eb6: 21 f4 brne .+8 ; 0x1ec0 <main+0xc0>

// UNIVERSAL command is ignored

getNch(4);

1eb8: 84 e0 ldi r24, 0x04 ; 4

1eba: 85 d0 rcall .+266 ; 0x1fc6 <getNch>

putch(0x00);

1ebc: 80 e0 ldi r24, 0x00 ; 0

1ebe: de cf rjmp .-68 ; 0x1e7c <main+0x7c>

}

/* Write memory, length is big endian and is in bytes */

else if(ch == STK_PROG_PAGE) {

1ec0: 84 36 cpi r24, 0x64 ; 100

1ec2: 09 f0 breq .+2 ; 0x1ec6 <main+0xc6>

1ec4: 40 c0 rjmp .+128 ; 0x1f46 <main+0x146>

// PROGRAM PAGE - we support flash programming only, not EEPROM

uint8_t *bufPtr;

uint16_t addrPtr;

getch(); /* getlen() */

1ec6: 6c d0 rcall .+216 ; 0x1fa0 <getch>

length = getch();

1ec8: 6b d0 rcall .+214 ; 0x1fa0 <getch>

1eca: 08 2f mov r16, r24

getch();

1ecc: 69 d0 rcall .+210 ; 0x1fa0 <getch>

// If we are in RWW section, immediately start page erase

if (address < NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);

1ece: 80 e0 ldi r24, 0x00 ; 0

1ed0: c8 16 cp r12, r24

1ed2: 88 e1 ldi r24, 0x18 ; 24

1ed4: d8 06 cpc r13, r24

1ed6: 18 f4 brcc .+6 ; 0x1ede <main+0xde>

1ed8: f6 01 movw r30, r12

1eda: b7 be out 0x37, r11 ; 55

1edc: e8 95 spm

1ede: c0 e0 ldi r28, 0x00 ; 0

1ee0: d1 e0 ldi r29, 0x01 ; 1

// While that is going on, read in page contents

bufPtr = buff;

do *bufPtr++ = getch();

1ee2: 5e d0 rcall .+188 ; 0x1fa0 <getch>

1ee4: 89 93 st Y+, r24

while (--length);

1ee6: 0c 17 cp r16, r28

1ee8: e1 f7 brne .-8 ; 0x1ee2 <main+0xe2>

// If we are in NRWW section, page erase has to be delayed until now.

// Todo: Take RAMPZ into account

if (address >= NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);

1eea: f0 e0 ldi r31, 0x00 ; 0

1eec: cf 16 cp r12, r31

1eee: f8 e1 ldi r31, 0x18 ; 24

1ef0: df 06 cpc r13, r31

1ef2: 18 f0 brcs .+6 ; 0x1efa <main+0xfa>

1ef4: f6 01 movw r30, r12

1ef6: b7 be out 0x37, r11 ; 55

1ef8: e8 95 spm

// Read command terminator, start reply

verifySpace();

1efa: 5d d0 rcall .+186 ; 0x1fb6 <verifySpace>

// If only a partial page is to be programmed, the erase might not be complete.

// So check that here

boot_spm_busy_wait();

1efc: 07 b6 in r0, 0x37 ; 55

1efe: 00 fc sbrc r0, 0

1f00: fd cf rjmp .-6 ; 0x1efc <main+0xfc>

1f02: a6 01 movw r20, r12

1f04: a0 e0 ldi r26, 0x00 ; 0

1f06: b1 e0 ldi r27, 0x01 ; 1

bufPtr = buff;

addrPtr = (uint16_t)(void*)address;

ch = SPM_PAGESIZE / 2;

do {

uint16_t a;

a = *bufPtr++;

1f08: 2c 91 ld r18, X

1f0a: 30 e0 ldi r19, 0x00 ; 0

a |= (*bufPtr++) << 8;

1f0c: 11 96 adiw r26, 0x01 ; 1

1f0e: 8c 91 ld r24, X

1f10: 11 97 sbiw r26, 0x01 ; 1

1f12: 90 e0 ldi r25, 0x00 ; 0

1f14: 98 2f mov r25, r24

1f16: 88 27 eor r24, r24

1f18: 82 2b or r24, r18

1f1a: 93 2b or r25, r19

#define rstVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+4))

#define wdtVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+6))

#endif

/* main program starts here */

int main(void) {

1f1c: 12 96 adiw r26, 0x02 ; 2

ch = SPM_PAGESIZE / 2;

do {

uint16_t a;

a = *bufPtr++;

a |= (*bufPtr++) << 8;

__boot_page_fill_short((uint16_t)(void*)addrPtr,a);

1f1e: fa 01 movw r30, r20

1f20: 0c 01 movw r0, r24

1f22: 87 be out 0x37, r8 ; 55

1f24: e8 95 spm

1f26: 11 24 eor r1, r1

addrPtr += 2;

1f28: 4e 5f subi r20, 0xFE ; 254

1f2a: 5f 4f sbci r21, 0xFF ; 255

} while (--ch);

1f2c: f1 e0 ldi r31, 0x01 ; 1

1f2e: a0 34 cpi r26, 0x40 ; 64

1f30: bf 07 cpc r27, r31

1f32: 51 f7 brne .-44 ; 0x1f08 <main+0x108>

// Write from programming buffer

__boot_page_write_short((uint16_t)(void*)address);

1f34: f6 01 movw r30, r12

1f36: a7 be out 0x37, r10 ; 55

1f38: e8 95 spm

boot_spm_busy_wait();

1f3a: 07 b6 in r0, 0x37 ; 55

1f3c: 00 fc sbrc r0, 0

1f3e: fd cf rjmp .-6 ; 0x1f3a <main+0x13a>

#if defined(RWWSRE)

// Reenable read access to flash

boot_rww_enable();

1f40: 97 be out 0x37, r9 ; 55

1f42: e8 95 spm

1f44: 26 c0 rjmp .+76 ; 0x1f92 <main+0x192>

#endif

}

/* Read memory block mode, length is big endian. */

else if(ch == STK_READ_PAGE) {

1f46: 84 37 cpi r24, 0x74 ; 116

1f48: b1 f4 brne .+44 ; 0x1f76 <main+0x176>

// READ PAGE - we only read flash

getch(); /* getlen() */

1f4a: 2a d0 rcall .+84 ; 0x1fa0 <getch>

length = getch();

1f4c: 29 d0 rcall .+82 ; 0x1fa0 <getch>

1f4e: f8 2e mov r15, r24

getch();

1f50: 27 d0 rcall .+78 ; 0x1fa0 <getch>

verifySpace();

1f52: 31 d0 rcall .+98 ; 0x1fb6 <verifySpace>

1f54: f6 01 movw r30, r12

1f56: ef 2c mov r14, r15

putch(result);

address++;

}

while (--length);

#else

do putch(pgm_read_byte_near(address++));

1f58: 8f 01 movw r16, r30

1f5a: 0f 5f subi r16, 0xFF ; 255

1f5c: 1f 4f sbci r17, 0xFF ; 255

1f5e: 84 91 lpm r24, Z+

1f60: 1b d0 rcall .+54 ; 0x1f98 <putch>

while (--length);

1f62: ea 94 dec r14

1f64: f8 01 movw r30, r16

1f66: c1 f7 brne .-16 ; 0x1f58 <main+0x158>

#define rstVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+4))

#define wdtVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+6))

#endif

/* main program starts here */

int main(void) {

1f68: 08 94 sec

1f6a: c1 1c adc r12, r1

1f6c: d1 1c adc r13, r1

1f6e: fa 94 dec r15

1f70: cf 0c add r12, r15

1f72: d1 1c adc r13, r1

1f74: 0e c0 rjmp .+28 ; 0x1f92 <main+0x192>

#endif

#endif

}

/* Get device signature bytes */

else if(ch == STK_READ_SIGN) {

1f76: 85 37 cpi r24, 0x75 ; 117

1f78: 39 f4 brne .+14 ; 0x1f88 <main+0x188>

// READ SIGN - return what Avrdude wants to hear

verifySpace();

1f7a: 1d d0 rcall .+58 ; 0x1fb6 <verifySpace>

putch(SIGNATURE_0);

1f7c: 8e e1 ldi r24, 0x1E ; 30

1f7e: 0c d0 rcall .+24 ; 0x1f98 <putch>

putch(SIGNATURE_1);

1f80: 83 e9 ldi r24, 0x93 ; 147

1f82: 0a d0 rcall .+20 ; 0x1f98 <putch>

putch(SIGNATURE_2);

1f84: 87 e0 ldi r24, 0x07 ; 7

1f86: 7a cf rjmp .-268 ; 0x1e7c <main+0x7c>

}

else if (ch == 'Q') {

1f88: 81 35 cpi r24, 0x51 ; 81

1f8a: 11 f4 brne .+4 ; 0x1f90 <main+0x190>

// Adaboot no-wait mod

watchdogConfig(WATCHDOG_16MS);

1f8c: 88 e0 ldi r24, 0x08 ; 8

1f8e: 0f d0 rcall .+30 ; 0x1fae <watchdogConfig>

verifySpace();

}

else {

// This covers the response to commands like STK_ENTER_PROGMODE

verifySpace();

1f90: 12 d0 rcall .+36 ; 0x1fb6 <verifySpace>

}

putch(STK_OK);

1f92: 80 e1 ldi r24, 0x10 ; 16

1f94: 01 d0 rcall .+2 ; 0x1f98 <putch>

1f96: 65 cf rjmp .-310 ; 0x1e62 <main+0x62>

00001f98 <putch>:

}

}

void putch(char ch) {

#ifndef SOFT_UART

while (!(UCSR0A & _BV(UDRE0)));

1f98: 5d 9b sbis 0x0b, 5 ; 11

1f9a: fe cf rjmp .-4 ; 0x1f98 <putch>

UDR0 = ch;

1f9c: 8c b9 out 0x0c, r24 ; 12

[uartBit] "I" (UART_TX_BIT)

:

"r25"

);

#endif

}

1f9e: 08 95 ret

00001fa0 <getch>:

[uartBit] "I" (UART_RX_BIT)

:

"r25"

);

#else

while(!(UCSR0A & _BV(RXC0)))

1fa0: 5f 9b sbis 0x0b, 7 ; 11

1fa2: fe cf rjmp .-4 ; 0x1fa0 <getch>

;

if (!(UCSR0A & _BV(FE0))) {

1fa4: 5c 99 sbic 0x0b, 4 ; 11

1fa6: 01 c0 rjmp .+2 ; 0x1faa <getch+0xa>

}

#endif

// Watchdog functions. These are only safe with interrupts turned off.

void watchdogReset() {

__asm__ __volatile__ (

1fa8: a8 95 wdr

* don't care that an invalid char is returned...)

*/

watchdogReset();

}

ch = UDR0;

1faa: 8c b1 in r24, 0x0c ; 12

LED_PIN |= _BV(LED);

#endif

#endif

return ch;

}

1fac: 08 95 ret

00001fae <watchdogConfig>:

"wdr\n"

);

}

void watchdogConfig(uint8_t x) {

WDTCSR = _BV(WDCE) | _BV(WDE);

1fae: 98 e1 ldi r25, 0x18 ; 24

1fb0: 91 bd out 0x21, r25 ; 33

WDTCSR = x;

1fb2: 81 bd out 0x21, r24 ; 33

}

1fb4: 08 95 ret

00001fb6 <verifySpace>:

do getch(); while (--count);

verifySpace();

}

void verifySpace() {

if (getch() != CRC_EOP) {

1fb6: f4 df rcall .-24 ; 0x1fa0 <getch>

1fb8: 80 32 cpi r24, 0x20 ; 32

1fba: 19 f0 breq .+6 ; 0x1fc2 <verifySpace+0xc>

watchdogConfig(WATCHDOG_16MS); // shorten WD timeout

1fbc: 88 e0 ldi r24, 0x08 ; 8

1fbe: f7 df rcall .-18 ; 0x1fae <watchdogConfig>

1fc0: ff cf rjmp .-2 ; 0x1fc0 <verifySpace+0xa>

while (1) // and busy-loop so that WD causes

; // a reset and app start.

}

putch(STK_INSYNC);

1fc2: 84 e1 ldi r24, 0x14 ; 20

}

1fc4: e9 cf rjmp .-46 ; 0x1f98 <putch>

00001fc6 <getNch>:

::[count] "M" (UART_B_VALUE)

);

}

#endif

void getNch(uint8_t count) {

1fc6: 1f 93 push r17

1fc8: 18 2f mov r17, r24

do getch(); while (--count);

1fca: ea df rcall .-44 ; 0x1fa0 <getch>

1fcc: 11 50 subi r17, 0x01 ; 1

1fce: e9 f7 brne .-6 ; 0x1fca <getNch+0x4>

verifySpace();

1fd0: f2 df rcall .-28 ; 0x1fb6 <verifySpace>

}

1fd2: 1f 91 pop r17

1fd4: 08 95 ret

00001fd6 <appStart>:

WDTCSR = _BV(WDCE) | _BV(WDE);

WDTCSR = x;

}

void appStart() {

watchdogConfig(WATCHDOG_OFF);

1fd6: 80 e0 ldi r24, 0x00 ; 0

1fd8: ea df rcall .-44 ; 0x1fae <watchdogConfig>

__asm__ __volatile__ (

1fda: ee 27 eor r30, r30

1fdc: ff 27 eor r31, r31

1fde: 09 94 ijmp