Can't connect to Zigbee Gateway (Tuya app) #11252

tvixen · 2025-04-14T16:20:16Z

tvixen
Apr 14, 2025

Board

ESP32C6

Device Description

I have 2 ESP32S3 and 2 ESP32C6,

Hardware Configuration

uint8_t led = RGB_BUILTIN;
uint8_t button = BOOT_PIN;

Version

v3.2.0

IDE Name

Arduino IDE 1.8.19

Operating System

Windows 10

Flash frequency

80Mhz

PSRAM enabled

yes

Upload speed

921600

Description

I use the the Arduino compiler IDE version 1.8.19, and is working very fine with ESP32S3 and all of my code using I2C, SPI, Wifi etc.
But when I use the ESP32C6 in Zigbee mode as end device, it seem to struggle a bit. It compiles fine with the examples in the library and uploads fine til the board. But it dosent seem to connect to my Zigbee gateway.

Any one who can clarify this for me?

Sketch

// Copyright 2024 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at

//     http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

/**
 * @brief This example demonstrates Zigbee Color Dimmable light bulb.
 *
 * The example demonstrates how to use Zigbee library to create an end device with
 * color dimmable light end point.
 * The light bulb is a Zigbee end device, which is controlled by a Zigbee coordinator.
 *
 * Proper Zigbee mode must be selected in Tools->Zigbee mode
 * and also the correct partition scheme must be selected in Tools->Partition Scheme.
 *
 * Please check the README.md for instructions and more detailed description.
 *
 * Created by Jan Procházka (https://github.com/P-R-O-C-H-Y/)
 */

#ifndef ZIGBEE_MODE_ED
#error "Zigbee end device mode is not selected in Tools->Zigbee mode"
#endif

#include "Zigbee.h"

/* Zigbee color dimmable light configuration */
#define ZIGBEE_RGB_LIGHT_ENDPOINT 10
uint8_t led = RGB_BUILTIN;
uint8_t button = BOOT_PIN;

ZigbeeColorDimmableLight zbColorLight = ZigbeeColorDimmableLight(ZIGBEE_RGB_LIGHT_ENDPOINT);

/********************* RGB LED functions **************************/
void setRGBLight(bool state, uint8_t red, uint8_t green, uint8_t blue, uint8_t level) {
  if (!state) {
    rgbLedWrite(led, 0, 0, 0);
    return;
  }
  float brightness = (float)level / 255;
  rgbLedWrite(led, red * brightness, green * brightness, blue * brightness);
}

// Create a task on identify call to handle the identify function
void identify(uint16_t time) {
  static uint8_t blink = 1;
  log_d("Identify called for %d seconds", time);
  if (time == 0) {
    // If identify time is 0, stop blinking and restore light as it was used for identify
    zbColorLight.restoreLight();
    return;
  }
  rgbLedWrite(led, 255 * blink, 255 * blink, 255 * blink);
  blink = !blink;
}

/********************* Arduino functions **************************/
void setup() {
  Serial.begin(115200);

  // Init RMT and leave light OFF
  rgbLedWrite(led, 0, 0, 0);

  // Init button for factory reset
  pinMode(button, INPUT_PULLUP);

  // Set callback function for light change
  zbColorLight.onLightChange(setRGBLight);

  // Optional: Set callback function for device identify
  zbColorLight.onIdentify(identify);

  // Optional: Set Zigbee device name and model
  zbColorLight.setManufacturerAndModel("Espressif", "ZBColorLightBulb");

  // Add endpoint to Zigbee Core
  Serial.println("Adding ZigbeeLight endpoint to Zigbee Core");
  Zigbee.addEndpoint(&zbColorLight);

  // When all EPs are registered, start Zigbee in End Device mode
  if (!Zigbee.begin()) {
    Serial.println("Zigbee failed to start!");
    Serial.println("Rebooting...");
    ESP.restart();
  }
  Serial.println("Connecting to network");
  while (!Zigbee.connected()) {
    Serial.print(".");
    delay(100);
  }
  Serial.println();
}

void loop() {
  // Checking button for factory reset
  if (digitalRead(button) == LOW) {  // Push button pressed
    // Key debounce handling
    delay(100);
    int startTime = millis();
    while (digitalRead(button) == LOW) {
      delay(50);
      if ((millis() - startTime) > 3000) {
        // If key pressed for more than 3secs, factory reset Zigbee and reboot
        Serial.println("Resetting Zigbee to factory and rebooting in 1s.");
        delay(1000);
        Zigbee.factoryReset();
      }
    }
    // Increase blightness by 50 every time the button is pressed
    zbColorLight.setLightLevel(zbColorLight.getLightLevel() + 50);
  }
  delay(100);
}

Debug Message

No debug info

Other Steps to Reproduce

No response

I have checked existing issues, online documentation and the Troubleshooting Guide

I confirm I have checked existing issues, online documentation and Troubleshooting guide.

P-R-O-C-H-Y · 2025-04-15T10:07:48Z

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

Hi @tvixen, can you post logs from the ESP (please set Core Debug Level to Verbose) and also some additional informations about your Zigbee network?

0 replies

tvixen · 2025-04-15T11:28:25Z

tvixen
Apr 15, 2025
Author

I can certainly do that, but I actually just wanted to know if I could continue using Arduino IDE 1.8.19 or if I should switch to IDE 2.0 before it will work with Zigbee?

As I worte, IDE 1.8.19 is working fine with ESP32S3.

0 replies

P-R-O-C-H-Y · 2025-04-15T11:29:42Z

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

I can certainly do that, but I actually just wanted to know if I could continue using Arduino IDE 1.8.19 or if I should switch to IDE 2.0 before it will work with Zigbee?

As I worte, IDE 1.8.19 is working fine with ESP32S3.

The IDE 1.8.19 is working. I am using that actually.

0 replies

tvixen · 2025-04-15T11:31:42Z

tvixen
Apr 15, 2025
Author

ok thanks for that. I will provide you the requested info asap.

0 replies

tvixen · 2025-04-15T12:29:35Z

tvixen
Apr 15, 2025
Author

Heres the log from ESP:
14:24:00.693 -> ESP-ROM:esp32c6-20220919
14:24:00.693 -> Build:Sep 19 2022
14:24:00.693 -> rst:0x1 (POWERON),boot:0xc (SPI_FAST_FLASH_BOOT)
14:24:00.693 -> SPIWP:0xee
14:24:00.693 -> mode:DIO, clock div:2
14:24:00.693 -> load:0x40875720,len:0x1260
14:24:00.693 -> load:0x4086c110,len:0xdc4
14:24:00.693 -> load:0x4086e610,len:0x3018
14:24:00.693 -> entry 0x4086c110
14:24:00.834 -> [ 0][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
14:24:00.881 -> [ 12][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
14:24:00.881 -> [ 23][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
14:24:00.881 -> [ 34][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
14:24:00.881 -> [ 46][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
14:24:00.881 -> [ 57][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
14:24:00.928 -> [ 68][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
14:24:00.928 -> [ 80][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
14:24:00.928 -> [ 91][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
14:24:00.928 -> [ 102][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
14:24:00.974 -> [ 114][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
14:24:00.974 -> [ 125][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
14:24:00.974 -> [ 136][V][ZigbeeEP.cpp:18] ZigbeeEP(): Endpoint: 10
14:24:00.974 -> [ 148][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 17 successfully set to type UART_RX (2) with bus 0x4080f280
14:24:01.021 -> [ 159][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 16 successfully set to type UART_TX (3) with bus 0x4080f280
14:24:01.021 -> =========== Before Setup Start ===========
14:24:01.021 -> Chip Info:
14:24:01.021 -> ------------------------------------------
14:24:01.021 -> Model : ESP32-C6
14:24:01.021 -> Package : 0
14:24:01.021 -> Revision : 0.01
14:24:01.021 -> Cores : 1
14:24:01.021 -> CPU Frequency : 160 MHz
14:24:01.021 -> XTAL Frequency : 40 MHz
14:24:01.021 -> Features Bitfield : 0x00000052
14:24:01.021 -> Embedded Flash : No
14:24:01.021 -> Embedded PSRAM : No
14:24:01.067 -> 2.4GHz WiFi : Yes
14:24:01.067 -> Classic BT : No
14:24:01.067 -> BT Low Energy : Yes
14:24:01.067 -> IEEE 802.15.4 : Yes
14:24:01.067 -> ------------------------------------------
14:24:01.067 -> INTERNAL Memory Info:
14:24:01.067 -> ------------------------------------------
14:24:01.067 -> Total Size : 445948 B ( 435.5 KB)
14:24:01.067 -> Free Bytes : 405808 B ( 396.3 KB)
14:24:01.067 -> Allocated Bytes : 32596 B ( 31.8 KB)
14:24:01.067 -> Minimum Free Bytes: 405808 B ( 396.3 KB)
14:24:01.067 -> Largest Free Block: 376820 B ( 368.0 KB)
14:24:01.067 -> ------------------------------------------
14:24:01.114 -> Flash Info:
14:24:01.114 -> ------------------------------------------
14:24:01.114 -> Chip Size : 8388608 B (8 MB)
14:24:01.114 -> Block Size : 65536 B ( 64.0 KB)
14:24:01.114 -> Sector Size : 4096 B ( 4.0 KB)
14:24:01.114 -> Page Size : 256 B ( 0.2 KB)
14:24:01.114 -> Bus Speed : 40 MHz
14:24:01.114 -> Bus Mode : QIO
14:24:01.114 -> ------------------------------------------
14:24:01.114 -> Partitions Info:
14:24:01.114 -> ------------------------------------------
14:24:01.114 -> nvs : addr: 0x00009000, size: 20.0 KB, type: DATA, subtype: NVS
14:24:01.114 -> otadata : addr: 0x0000E000, size: 8.0 KB, type: DATA, subtype: OTA
14:24:01.114 -> app0 : addr: 0x00010000, size: 1280.0 KB, type: APP, subtype: OTA_0
14:24:01.162 -> app1 : addr: 0x00150000, size: 1280.0 KB, type: APP, subtype: OTA_1
14:24:01.162 -> spiffs : addr: 0x00290000, size: 1388.0 KB, type: DATA, subtype: SPIFFS
14:24:01.162 -> zb_storage : addr: 0x003EB000, size: 16.0 KB, type: DATA, subtype: FAT
14:24:01.162 -> zb_fct : addr: 0x003EF000, size: 4.0 KB, type: DATA, subtype: FAT
14:24:01.162 -> coredump : addr: 0x003F0000, size: 64.0 KB, type: DATA, subtype: COREDUMP
14:24:01.207 -> ------------------------------------------
14:24:01.207 -> Software Info:
14:24:01.207 -> ------------------------------------------
14:24:01.207 -> Compile Date/Time : Apr 15 2025 14:22:18
14:24:01.207 -> Compile Host OS : windows
14:24:01.207 -> ESP-IDF Version : v5.4.1-1-g2f7dcd862a-dirty
14:24:01.207 -> Arduino Version : 3.2.0
14:24:01.207 -> ------------------------------------------
14:24:01.207 -> Board Info:
14:24:01.207 -> ------------------------------------------
14:24:01.207 -> Arduino Board : ESP32C6_DEV
14:24:01.207 -> Arduino Variant : esp32c6
14:24:01.207 -> Arduino FQBN : esp32:esp32:esp32c6:JTAGAdapter=default,CDCOnBoot=default,PartitionScheme=zigbee,CPUFreq=160,FlashMode=qio,FlashFreq=80,FlashSize=4M,UploadSpeed=921600,DebugLevel=verbose,EraseFlash=all,ZigbeeMode=ed
14:24:01.254 -> ============ Before Setup End ============
14:24:01.346 -> [ 500][V][esp32-hal-uart.c:552] uartBegin(): UART0 baud(115200) Mode(800001c) rxPin(17) txPin(16)
14:24:01.346 -> [ 509][V][esp32-hal-uart.c:650] uartBegin(): UART0 not installed. Starting installation
14:24:01.346 -> [ 517][V][esp32-hal-uart.c:660] uartBegin(): UART0 RX FIFO full threshold set to 120 (value requested: 120 || FIFO Max = 128)
14:24:01.393 -> [ 528][V][esp32-hal-uart.c:677] uartBegin(): Setting UART0 to use XTAL clock
14:24:01.393 -> [ 536][V][esp32-hal-uart.c:732] uartBegin(): UART0 initialization done.
14:24:01.393 -> [ 542][V][esp32-hal-uart.c:783] uartSetRxFIFOFull(): UART0 RX FIFO Full value set to 120 from a requested value of 120
14:24:01.393 -> [ 553][V][esp32-hal-rmt.c:454] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
14:24:01.393 -> [ 561][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x42005ab8
14:24:01.439 -> [ 573][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x42005ab8
14:24:01.439 -> [ 584][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x4081b0cc
14:24:01.439 -> [ 595][V][esp32-hal-rmt.c:305] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
14:24:01.439 -> [ 604][V][esp32-hal-rmt.c:306] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Asked to Loop: NO, LoopCancel: NO
14:24:01.439 -> [ 615][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x42004876
14:24:01.486 -> [ 626][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 9 successfully set to type GPIO (1) with bus 0xa
14:24:01.486 -> Adding ZigbeeLight endpoint to Zigbee Core
14:24:01.486 -> [ 636][D][ZigbeeCore.cpp:97] addEndpoint(): Endpoint: 10, Device ID: 0x0102
14:24:01.486 -> [ 647][D][ZigbeeCore.cpp:145] zigbeeInit(): Initialize Zigbee stack
14:24:01.579 -> [ 731][D][ZigbeeCore.cpp:152] zigbeeInit(): Register all Zigbee EPs in list
14:24:01.579 -> [ 739][I][ZigbeeCore.cpp:160] zigbeeInit(): List of registered Zigbee EPs:
14:24:01.579 -> [ 746][I][ZigbeeCore.cpp:162] zigbeeInit(): Device type: Color Dimmable Light Device, Endpoint: 10, Device ID: 0x0102
14:24:01.626 -> [ 760][V][ZigbeeCore.cpp:379] esp_zb_app_signal_handler(): ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
14:24:01.626 -> [ 770][I][ZigbeeCore.cpp:241] esp_zb_app_signal_handler(): Zigbee stack initialized
14:24:01.626 -> [ 778][D][ZigbeeCore.cpp:242] esp_zb_app_signal_handler(): Zigbee channel mask: 0x07fff800
14:24:01.626 -> [ 787][I][ZigbeeCore.cpp:248] esp_zb_app_signal_handler(): Device started up in factory-reset mode
14:24:01.626 -> [ 796][I][ZigbeeCore.cpp:255] esp_zb_app_signal_handler(): Start network steering
14:24:01.672 -> Connecting to network
14:24:01.672 -> .......................[ 3031][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:03.924 -> ................................[ 6269][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:07.151 -> ................................[ 9507][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:10.370 -> .................................[ 12744][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:13.641 -> ................................[ 15982][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:16.860 -> ................................[ 19219][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:20.075 -> .................................[ 22457][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:23.389 -> ................................[ 25695][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:26.561 -> .................................[ 28933][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:29.871 -> ................................[ 32171][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:33.083 -> ................................[ 35409][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:36.255 -> .................................[ 38647][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:39.571 -> ................................[ 41885][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:42.787 -> ................................[ 45123][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:45.961 -> .................................[ 48361][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:49.268 -> ................................[ 51599][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:52.490 -> .................................[ 54837][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:55.753 -> ................................[ 58075][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:24:58.964 -> ................................[ 61312][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:02.180 -> .................................[ 64550][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:05.492 -> ................................[ 67788][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:08.666 -> ................................[ 71026][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:11.884 -> .................................[ 74264][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:15.200 -> ................................[ 77501][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:18.373 -> .................................[ 80739][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:21.677 -> ................................[ 83976][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:24.898 -> ................................[ 87214][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:28.069 -> .................................[ 90452][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:31.384 -> ................................[ 93690][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:34.596 -> ................................[ 96928][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:37.765 -> .................................[100166][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:41.070 -> ................................[103403][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:44.281 -> .................................[106641][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:47.593 -> ................................[109879][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:50.771 -> ................................[113117][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:53.989 -> .................................[116355][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:25:57.293 -> ................................[119593][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:00.460 -> ................................[122831][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:03.673 -> .................................[126069][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:06.979 -> ................................[129307][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:10.196 -> .................................[132545][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:13.469 -> ................................[135783][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:16.687 -> ................................[139021][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:19.901 -> .................................[142259][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:23.166 -> ................................[145496][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:26.386 -> ................................[148734][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:29.606 -> .................................[151972][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:32.871 -> ................................[155210][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:36.094 -> .................................[158448][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:39.402 -> ................................[161686][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:42.574 -> ................................[164924][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:45.790 -> .................................[168162][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:49.098 -> ................................[171400][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:52.269 -> ................................[174638][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:55.481 -> .................................[177876][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:26:58.777 -> ................................[181114][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:02.002 -> .................................[184351][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:05.310 -> ................................[187589][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:08.475 -> ................................[190827][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:11.692 -> .................................[194065][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:15.010 -> ................................[197303][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:18.177 -> ................................[200541][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:21.393 -> .................................[203778][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
14:27:24.703 -> ......................................[207626][I][ZigbeeCore.cpp:308] esp_zb_app_signal_handler(): Joined network successfully (Extended PAN ID: 4b:a0:61:84:42:21:a4:e3, PAN ID: 0x04a6, Channel:20, Short Address: 0x1a00)
14:27:28.481 -> [207644][V][ZigbeeCore.cpp:527] setNVRAMChannelMask(): Channel mask set to 0x00100000
14:27:28.481 ->
14:27:28.481 -> =========== After Setup Start ============
14:27:28.481 -> INTERNAL Memory Info:
14:27:28.526 -> ------------------------------------------
14:27:28.526 -> Total Size : 445948 B ( 435.5 KB)
14:27:28.526 -> Free Bytes : 375840 B ( 367.0 KB)
14:27:28.526 -> Allocated Bytes : 61588 B ( 60.1 KB)
14:27:28.526 -> Minimum Free Bytes: 375840 B ( 367.0 KB)
14:27:28.526 -> Largest Free Block: 344052 B ( 336.0 KB)
14:27:28.526 -> ------------------------------------------
14:27:28.526 -> GPIO Info:
14:27:28.526 -> ------------------------------------------
14:27:28.526 -> GPIO : BUS_TYPE[bus/unit][chan]
14:27:28.526 -> --------------------------------------
14:27:28.526 -> 8 : RMT_TX
14:27:28.526 -> 9 : GPIO
14:27:28.572 -> 16 : UART_TX[0]
14:27:28.572 -> 17 : UART_RX[0]
14:27:28.572 -> ============ After Setup End =============

0 replies

P-R-O-C-H-Y · 2025-04-15T12:51:40Z

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

I see in the logs that after many tries it has successfully joined the network:

4:27:24.703 -> 207626][I][ZigbeeCore.cpp:308] esp_zb_app_signal_handler(): Joined network successfully (Extended PAN ID: 4b:a0:61:84:42:21:a4:e3, PAN ID: 0x04a6, Channel:20, Short Address: 0x1a00)

So where is actually the issue? We are running Zigbee devices on ESPs without any problems.

0 replies

tvixen · 2025-04-15T12:56:55Z

tvixen
Apr 15, 2025
Author

Yes, but my Tuya app says "no new devices found"

Im a supposed to delete the old device in the Tuya app before adding a new function to the Zigbee device?

0 replies

P-R-O-C-H-Y · 2025-04-15T12:59:05Z

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

For sure, when flashing new firmware to ESP, remove the device first , flash and add again.
Also set Erase Flash before upload to Enabled in the IDE Tools menu.

But TBH I am not sure if the ESP is supposed to work under Tuya app. I did not see anyone trying that before.
If you can share more details on how is the process and if that works It would be nice.

0 replies

P-R-O-C-H-Y · 2025-04-15T13:00:56Z

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

I did transfer you issue to discussions, as there is no real issue :)

0 replies

tvixen · 2025-04-15T13:19:35Z

tvixen
Apr 15, 2025
Author

Thats ok.

So I deleted the device in Tuya app , and tried to add it again. No luck: "no new devices found"
The process is pretty simple. You just go to Add device, and if your stone sure its a Zigbee device, you can jump direct to the Zigbee search.

I tried another examples (Zigbee_Light_on_off) and this appear in Tuya ... and I can turn off and on the little LED on the board with the Tuya app.

I checked the Tuya app, for dimming light, and it has a what they call "Light modulator" so I guess its supported

Heres the new log after deletion of the device:

15:21:34.986 -> ESP-ROM:esp32c6-20220919
15:21:34.986 -> Build:Sep 19 2022
15:21:34.986 -> rst:0x1 (POWERON),boot:0xc (SPI_FAST_FLASH_BOOT)
15:21:34.986 -> SPIWP:0xee
15:21:34.986 -> mode:DIO, clock div:2
15:21:34.986 -> load:0x40875720,len:0x1260
15:21:34.986 -> load:0x4086c110,len:0xdc4
15:21:34.986 -> load:0x4086e610,len:0x3018
15:21:34.986 -> entry 0x4086c110
15:21:35.126 -> [     0][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
15:21:35.126 -> [    12][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
15:21:35.126 -> [    23][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
15:21:35.173 -> [    34][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
15:21:35.173 -> [    46][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
15:21:35.173 -> [    57][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
15:21:35.173 -> [    68][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
15:21:35.220 -> [    80][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
15:21:35.220 -> [    91][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
15:21:35.220 -> [   102][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
15:21:35.220 -> [   114][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
15:21:35.220 -> [   125][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
15:21:35.267 -> [   136][V][ZigbeeEP.cpp:18] ZigbeeEP(): Endpoint: 10
15:21:35.267 -> [   148][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 17 successfully set to type UART_RX (2) with bus 0x4080f280
15:21:35.267 -> [   159][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 16 successfully set to type UART_TX (3) with bus 0x4080f280
15:21:35.267 -> =========== Before Setup Start ===========
15:21:35.267 -> Chip Info:
15:21:35.267 -> ------------------------------------------
15:21:35.313 ->   Model             : ESP32-C6
15:21:35.313 ->   Package           : 0
15:21:35.313 ->   Revision          : 0.01
15:21:35.313 ->   Cores             : 1
15:21:35.313 ->   CPU Frequency     : 160 MHz
15:21:35.313 ->   XTAL Frequency    : 40 MHz
15:21:35.313 ->   Features Bitfield : 0x00000052
15:21:35.313 ->   Embedded Flash    : No
15:21:35.313 ->   Embedded PSRAM    : No
15:21:35.313 ->   2.4GHz WiFi       : Yes
15:21:35.313 ->   Classic BT        : No
15:21:35.313 ->   BT Low Energy     : Yes
15:21:35.313 ->   IEEE 802.15.4     : Yes
15:21:35.313 -> ------------------------------------------
15:21:35.313 -> INTERNAL Memory Info:
15:21:35.313 -> ------------------------------------------
15:21:35.313 ->   Total Size        :   445948 B ( 435.5 KB)
15:21:35.360 ->   Free Bytes        :   405664 B ( 396.2 KB)
15:21:35.360 ->   Allocated Bytes   :    32724 B (  32.0 KB)
15:21:35.360 ->   Minimum Free Bytes:   405664 B ( 396.2 KB)
15:21:35.360 ->   Largest Free Block:   376820 B ( 368.0 KB)
15:21:35.360 -> ------------------------------------------
15:21:35.360 -> Flash Info:
15:21:35.360 -> ------------------------------------------
15:21:35.360 ->   Chip Size         :  8388608 B (8 MB)
15:21:35.360 ->   Block Size        :    65536 B (  64.0 KB)
15:21:35.360 ->   Sector Size       :     4096 B (   4.0 KB)
15:21:35.360 ->   Page Size         :      256 B (   0.2 KB)
15:21:35.360 ->   Bus Speed         : 40 MHz
15:21:35.406 ->   Bus Mode          : QIO
15:21:35.406 -> ------------------------------------------
15:21:35.406 -> Partitions Info:
15:21:35.406 -> ------------------------------------------
15:21:35.406 ->                 nvs : addr: 0x00009000, size:    20.0 KB, type: DATA, subtype: NVS
15:21:35.406 ->             otadata : addr: 0x0000E000, size:     8.0 KB, type: DATA, subtype: OTA
15:21:35.406 ->                app0 : addr: 0x00010000, size:  1280.0 KB, type:  APP, subtype: OTA_0
15:21:35.406 ->                app1 : addr: 0x00150000, size:  1280.0 KB, type:  APP, subtype: OTA_1
15:21:35.406 ->              spiffs : addr: 0x00290000, size:  1388.0 KB, type: DATA, subtype: SPIFFS
15:21:35.454 ->          zb_storage : addr: 0x003EB000, size:    16.0 KB, type: DATA, subtype: FAT
15:21:35.454 ->              zb_fct : addr: 0x003EF000, size:     4.0 KB, type: DATA, subtype: FAT
15:21:35.454 ->            coredump : addr: 0x003F0000, size:    64.0 KB, type: DATA, subtype: COREDUMP
15:21:35.454 -> ------------------------------------------
15:21:35.454 -> Software Info:
15:21:35.454 -> ------------------------------------------
15:21:35.454 ->   Compile Date/Time : Apr 15 2025 14:22:18
15:21:35.454 ->   Compile Host OS   : windows
15:21:35.454 ->   ESP-IDF Version   : v5.4.1-1-g2f7dcd862a-dirty
15:21:35.454 ->   Arduino Version   : 3.2.0
15:21:35.500 -> ------------------------------------------
15:21:35.500 -> Board Info:
15:21:35.500 -> ------------------------------------------
15:21:35.500 ->   Arduino Board     : ESP32C6_DEV
15:21:35.500 ->   Arduino Variant   : esp32c6
15:21:35.500 ->   Arduino FQBN      : esp32:esp32:esp32c6:JTAGAdapter=default,CDCOnBoot=default,PartitionScheme=zigbee,CPUFreq=160,FlashMode=qio,FlashFreq=80,FlashSize=4M,UploadSpeed=921600,DebugLevel=verbose,EraseFlash=all,ZigbeeMode=ed
15:21:35.500 -> ============ Before Setup End ============
15:21:35.642 -> [   499][V][esp32-hal-uart.c:552] uartBegin(): UART0 baud(115200) Mode(800001c) rxPin(17) txPin(16)
15:21:35.642 -> [   508][V][esp32-hal-uart.c:650] uartBegin(): UART0 not installed. Starting installation
15:21:35.642 -> [   516][V][esp32-hal-uart.c:660] uartBegin(): UART0 RX FIFO full threshold set to 120 (value requested: 120 || FIFO Max = 128)
15:21:35.642 -> [   527][V][esp32-hal-uart.c:677] uartBegin(): Setting UART0 to use XTAL clock
15:21:35.642 -> [   535][V][esp32-hal-uart.c:732] uartBegin(): UART0 initialization done.
15:21:35.642 -> [   541][V][esp32-hal-uart.c:783] uartSetRxFIFOFull(): UART0 RX FIFO Full value set to 120 from a requested value of 120
15:21:35.689 -> [   552][V][esp32-hal-rmt.c:454] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
15:21:35.689 -> [   560][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x42005ab8
15:21:35.689 -> [   572][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x42005ab8
15:21:35.689 -> [   583][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x4081b0cc
15:21:35.689 -> [   594][V][esp32-hal-rmt.c:305] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
15:21:35.735 -> [   603][V][esp32-hal-rmt.c:306] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Asked to Loop: NO, LoopCancel: NO
15:21:35.735 -> [   614][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x42004876
15:21:35.735 -> [   625][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 9 successfully set to type GPIO (1) with bus 0xa
15:21:35.735 -> Adding ZigbeeLight endpoint to Zigbee Core
15:21:35.735 -> [   635][D][ZigbeeCore.cpp:97] addEndpoint(): Endpoint: 10, Device ID: 0x0102
15:21:35.782 -> [   646][D][ZigbeeCore.cpp:145] zigbeeInit(): Initialize Zigbee stack
15:21:35.875 -> [   734][D][ZigbeeCore.cpp:152] zigbeeInit(): Register all Zigbee EPs in list
15:21:35.875 -> [   743][I][ZigbeeCore.cpp:160] zigbeeInit(): List of registered Zigbee EPs:
15:21:35.875 -> [   750][I][ZigbeeCore.cpp:162] zigbeeInit(): Device type: Color Dimmable Light Device, Endpoint: 10, Device ID: 0x0102
15:21:35.875 -> [   766][V][ZigbeeCore.cpp:379] esp_zb_app_signal_handler(): ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
15:21:35.875 -> [   776][I][ZigbeeCore.cpp:241] esp_zb_app_signal_handler(): Zigbee stack initialized
15:21:35.921 -> [   784][D][ZigbeeCore.cpp:242] esp_zb_app_signal_handler(): Zigbee channel mask: 0x00100000
15:21:36.155 -> [  1058][I][ZigbeeCore.cpp:248] esp_zb_app_signal_handler(): Device started up in non factory-reset mode
15:21:36.201 -> [  1067][I][ZigbeeCore.cpp:261] esp_zb_app_signal_handler(): Device rebooted
15:21:36.201 -> [  1075][V][ZigbeeCore.cpp:527] setNVRAMChannelMask(): Channel mask set to 0x00100000
15:21:36.201 -> [  1083][D][ZigbeeCore.cpp:512] searchBindings(): Requesting binding table for address 0x1320
15:21:36.201 -> [  1092][D][ZigbeeCore.cpp:452] bindingTableCb(): Binding table callback for address 0x1320 with status 0
15:21:36.201 -> [  1101][D][ZigbeeCore.cpp:455] bindingTableCb(): Binding table info: total 0, index 0, count 0
15:21:36.247 -> [  1110][D][ZigbeeCore.cpp:458] bindingTableCb(): No binding table entries found
15:21:36.247 -> Connecting to network
15:21:36.247 -> 
15:21:36.247 -> =========== After Setup Start ============
15:21:36.247 -> INTERNAL Memory Info:
15:21:36.247 -> ------------------------------------------
15:21:36.247 ->   Total Size        :   445948 B ( 435.5 KB)
15:21:36.247 ->   Free Bytes        :   375696 B ( 366.9 KB)
15:21:36.247 ->   Allocated Bytes   :    61716 B (  60.3 KB)
15:21:36.294 -> [  1156][V][ZigbeeCore.cpp:385] factoryReset(): Factory resetting Zigbee stack, device will reboot
15:21:36.340 ->   Minimum Free Bytes:   375696 B ( 366.9 KB)
15:21:36.340 ->   Largest Free Block:   344052 B ( 336.0 KB)
15:21:36.386 -> ------------------------------------------
15:21:36.433 -> GPIO Info:
15:21:36.433 -> ------------------------------------------
15:21:36.433 -> ESP-ROM:esp32c6-20220919
15:21:36.433 -> Build:Sep 19 2022
15:21:36.433 -> rst:0xc (SW_CPU),boot:0xc (SPI_FAST_FLASH_BOOT)
15:21:36.479 -> Saved PC:0x4001975a
15:21:36.479 -> SPIWP:0xee
15:21:36.479 -> mode:DIO, clock div:2
15:21:36.479 -> load:0x40875720,len:0x1260
15:21:36.479 -> load:0x4086c110,len:0xdc4
15:21:36.479 -> load:0x4086e610,len:0x3018
15:21:36.479 -> entry 0x4086c110
15:21:36.712 -> [     0][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
15:21:36.712 -> [    12][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
15:21:36.759 -> [    23][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
15:21:36.759 -> [    34][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
15:21:36.759 -> [    46][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
15:21:36.759 -> [    57][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
15:21:36.806 -> [    68][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
15:21:36.806 -> [    80][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
15:21:36.806 -> [    91][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RX (2) successfully set to 0x420081c2
15:21:36.806 -> [   102][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_TX (3) successfully set to 0x420081b0
15:21:36.852 -> [   114][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_CTS (4) successfully set to 0x4200819e
15:21:36.852 -> [   125][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type UART_RTS (5) successfully set to 0x4200818c
15:21:36.852 -> [   136][V][ZigbeeEP.cpp:18] ZigbeeEP(): Endpoint: 10
15:21:36.852 -> [   148][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 17 successfully set to type UART_RX (2) with bus 0x4080f280
15:21:36.852 -> [   159][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 16 successfully set to type UART_TX (3) with bus 0x4080f280
15:21:36.898 -> =========== Before Setup Start ===========
15:21:36.898 -> Chip Info:
15:21:36.898 -> ------------------------------------------
15:21:36.898 ->   Model             : ESP32-C6
15:21:36.898 ->   Package           : 0
15:21:36.898 ->   Revision          : 0.01
15:21:36.898 ->   Cores             : 1
15:21:36.898 ->   CPU Frequency     : 160 MHz
15:21:36.898 ->   XTAL Frequency    : 40 MHz
15:21:36.898 ->   Features Bitfield : 0x00000052
15:21:36.898 ->   Embedded Flash    : No
15:21:36.898 ->   Embedded PSRAM    : No
15:21:36.898 ->   2.4GHz WiFi       : Yes
15:21:36.898 ->   Classic BT        : No
15:21:36.946 ->   BT Low Energy     : Yes
15:21:36.946 ->   IEEE 802.15.4     : Yes
15:21:36.946 -> ------------------------------------------
15:21:36.946 -> INTERNAL Memory Info:
15:21:36.946 -> ------------------------------------------
15:21:36.946 ->   Total Size        :   445948 B ( 435.5 KB)
15:21:36.946 ->   Free Bytes        :   405664 B ( 396.2 KB)
15:21:36.946 ->   Allocated Bytes   :    32724 B (  32.0 KB)
15:21:36.946 ->   Minimum Free Bytes:   405664 B ( 396.2 KB)
15:21:36.946 ->   Largest Free Block:   376820 B ( 368.0 KB)
15:21:36.946 -> ------------------------------------------
15:21:36.946 -> Flash Info:
15:21:36.946 -> ------------------------------------------
15:21:36.946 ->   Chip Size         :  8388608 B (8 MB)
15:21:36.991 ->   Block Size        :    65536 B (  64.0 KB)
15:21:36.991 ->   Sector Size       :     4096 B (   4.0 KB)
15:21:36.991 ->   Page Size         :      256 B (   0.2 KB)
15:21:36.991 ->   Bus Speed         : 40 MHz
15:21:36.991 ->   Bus Mode          : QIO
15:21:36.991 -> ------------------------------------------
15:21:36.991 -> Partitions Info:
15:21:36.991 -> ------------------------------------------
15:21:36.991 ->                 nvs : addr: 0x00009000, size:    20.0 KB, type: DATA, subtype: NVS
15:21:36.991 ->             otadata : addr: 0x0000E000, size:     8.0 KB, type: DATA, subtype: OTA
15:21:36.991 ->                app0 : addr: 0x00010000, size:  1280.0 KB, type:  APP, subtype: OTA_0
15:21:37.038 ->                app1 : addr: 0x00150000, size:  1280.0 KB, type:  APP, subtype: OTA_1
15:21:37.038 ->              spiffs : addr: 0x00290000, size:  1388.0 KB, type: DATA, subtype: SPIFFS
15:21:37.038 ->          zb_storage : addr: 0x003EB000, size:    16.0 KB, type: DATA, subtype: FAT
15:21:37.038 ->              zb_fct : addr: 0x003EF000, size:     4.0 KB, type: DATA, subtype: FAT
15:21:37.038 ->            coredump : addr: 0x003F0000, size:    64.0 KB, type: DATA, subtype: COREDUMP
15:21:37.038 -> ------------------------------------------
15:21:37.038 -> Software Info:
15:21:37.038 -> ------------------------------------------
15:21:37.085 ->   Compile Date/Time : Apr 15 2025 14:22:18
15:21:37.085 ->   Compile Host OS   : windows
15:21:37.085 ->   ESP-IDF Version   : v5.4.1-1-g2f7dcd862a-dirty
15:21:37.085 ->   Arduino Version   : 3.2.0
15:21:37.085 -> ------------------------------------------
15:21:37.085 -> Board Info:
15:21:37.085 -> ------------------------------------------
15:21:37.085 ->   Arduino Board     : ESP32C6_DEV
15:21:37.085 ->   Arduino Variant   : esp32c6
15:21:37.085 ->   Arduino FQBN      : esp32:esp32:esp32c6:JTAGAdapter=default,CDCOnBoot=default,PartitionScheme=zigbee,CPUFreq=160,FlashMode=qio,FlashFreq=80,FlashSize=4M,UploadSpeed=921600,DebugLevel=verbose,EraseFlash=all,ZigbeeMode=ed
15:21:37.132 -> ============ Before Setup End ============
15:21:37.225 -> [   499][V][esp32-hal-uart.c:552] uartBegin(): UART0 baud(115200) Mode(800001c) rxPin(17) txPin(16)
15:21:37.225 -> [   508][V][esp32-hal-uart.c:650] uartBegin(): UART0 not installed. Starting installation
15:21:37.225 -> [   516][V][esp32-hal-uart.c:660] uartBegin(): UART0 RX FIFO full threshold set to 120 (value requested: 120 || FIFO Max = 128)
15:21:37.225 -> [   527][V][esp32-hal-uart.c:677] uartBegin(): Setting UART0 to use XTAL clock
15:21:37.272 -> [   535][V][esp32-hal-uart.c:732] uartBegin(): UART0 initialization done.
15:21:37.272 -> [   541][V][esp32-hal-uart.c:783] uartSetRxFIFOFull(): UART0 RX FIFO Full value set to 120 from a requested value of 120
15:21:37.272 -> [   552][V][esp32-hal-rmt.c:454] rmtInit(): GPIO 8 - TX MODE - MemSize[48] - Freq=10000000Hz
15:21:37.272 -> [   560][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_TX (10) successfully set to 0x42005ab8
15:21:37.272 -> [   572][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type RMT_RX (11) successfully set to 0x42005ab8
15:21:37.319 -> [   583][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 8 successfully set to type RMT_TX (10) with bus 0x4081b0cc
15:21:37.319 -> [   594][V][esp32-hal-rmt.c:305] _rmtWrite(): GPIO: 8 - Request: 24 RMT Symbols - Blocking - Timeout: -1
15:21:37.319 -> [   603][V][esp32-hal-rmt.c:306] _rmtWrite(): GPIO: 8 - Currently in Loop Mode: [NO] | Asked to Loop: NO, LoopCancel: NO
15:21:37.319 -> [   614][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x42004876
15:21:37.367 -> [   625][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 9 successfully set to type GPIO (1) with bus 0xa
15:21:37.367 -> Adding ZigbeeLight endpoint to Zigbee Core
15:21:37.367 -> [   635][D][ZigbeeCore.cpp:97] addEndpoint(): Endpoint: 10, Device ID: 0x0102
15:21:37.367 -> [   646][D][ZigbeeCore.cpp:145] zigbeeInit(): Initialize Zigbee stack
15:21:37.460 -> [   734][D][ZigbeeCore.cpp:152] zigbeeInit(): Register all Zigbee EPs in list
15:21:37.460 -> [   742][I][ZigbeeCore.cpp:160] zigbeeInit(): List of registered Zigbee EPs:
15:21:37.460 -> [   749][I][ZigbeeCore.cpp:162] zigbeeInit(): Device type: Color Dimmable Light Device, Endpoint: 10, Device ID: 0x0102
15:21:37.506 -> [   763][V][ZigbeeCore.cpp:379] esp_zb_app_signal_handler(): ZDO signal: ZDO Config Ready (0x17), status: ESP_FAIL
15:21:37.506 -> [   773][I][ZigbeeCore.cpp:241] esp_zb_app_signal_handler(): Zigbee stack initialized
15:21:37.506 -> [   781][D][ZigbeeCore.cpp:242] esp_zb_app_signal_handler(): Zigbee channel mask: 0x07fff800
15:21:37.506 -> [   790][I][ZigbeeCore.cpp:248] esp_zb_app_signal_handler(): Device started up in  factory-reset mode
15:21:37.506 -> [   799][I][ZigbeeCore.cpp:255] esp_zb_app_signal_handler(): Start network steering
15:21:37.506 -> Connecting to network
15:21:37.506 -> .......................[  3033][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
15:21:39.838 -> ................................[  6271][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
15:21:43.009 -> ................................[  9509][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
15:21:46.224 -> .................................[ 12747][I][ZigbeeCore.cpp:317] esp_zb_app_signal_handler(): Network steering was not successful (status: ESP_FAIL)
15:21:49.538 -> ......................................[ 16615][I][ZigbeeCore.cpp:308] esp_zb_app_signal_handler(): Joined network successfully (Extended PAN ID: 4b:a0:61:84:42:21:a4:e3, PAN ID: 0x04a6, Channel:20, Short Address: 0x1320)
15:21:53.358 -> [ 16632][V][ZigbeeCore.cpp:527] setNVRAMChannelMask(): Channel mask set to 0x00100000
15:21:53.358 -> 
15:21:53.358 -> =========== After Setup Start ============
15:21:53.358 -> INTERNAL Memory Info:
15:21:53.358 -> ------------------------------------------
15:21:53.358 ->   Total Size        :   445948 B ( 435.5 KB)
15:21:53.358 ->   Free Bytes        :   375696 B ( 366.9 KB)
15:21:53.405 ->   Allocated Bytes   :    61716 B (  60.3 KB)
15:21:53.405 ->   Minimum Free Bytes:   375696 B ( 366.9 KB)
15:21:53.405 ->   Largest Free Block:   344052 B ( 336.0 KB)
15:21:53.405 -> ------------------------------------------
15:21:53.405 -> GPIO Info:
15:21:53.405 -> ------------------------------------------
15:21:53.405 ->   GPIO : BUS_TYPE[bus/unit][chan]
15:21:53.405 ->   --------------------------------------  
15:21:53.405 ->      8 : RMT_TX
15:21:53.405 ->      9 : GPIO
15:21:53.405 ->     16 : UART_TX[0]
15:21:53.405 ->     17 : UART_RX[0]
15:21:53.405 -> ============ After Setup End =============
15:21:53.682 -> [ 16944][V][ZigbeeCore.cpp:379] esp_zb_app_signal_handler(): ZDO signal: NLME Status Indication (0x32), status: ESP_OK

2 replies

P-R-O-C-H-Y Apr 15, 2025
Maintainer

Can't tell why the Color Dimmable Light doesn't work. On the ESP side everything is fine and the ESP connects to the network and obtains an address:

[ 16615][I][ZigbeeCore.cpp:308] esp_zb_app_signal_handler(): Joined network successfully (Extended PAN ID: 4b:a0:61:84:42:21:a4:e3, PAN ID: 0x04a6, Channel:20, Short Address: 0x1320)

You will need some logs from the TUYA to see what is wrong there. All examples which are included works with HomeAssistant, so there is nothing to be fixed.

tvixen Apr 15, 2025
Author

I think your right, it must be the Tuya app which has problems placing them in the right category, and therefore does not show them, even though they are apparently found. I'm not gonna find any logs from the Tuya app, as this is closed land.

But thanks for clarifying, much appreciated 👍

tvixen · 2025-05-02T15:52:55Z

tvixen
May 2, 2025
Author

I have tried with different Zigbee modes and examples, and for now, it seems that Tuya only support Temp, Humidity sensor, and Light sensor. Anything else it will not accecpt as a Zigbee device.

Is there any other app I can use, without making my own home automation server?

0 replies

Can't connect to Zigbee Gateway (Tuya app) #11252

Uh oh!

tvixen Apr 14, 2025

Board

Device Description

Hardware Configuration

Version

IDE Name

Operating System

Flash frequency

PSRAM enabled

Upload speed

Description

Sketch

Debug Message

Other Steps to Reproduce

I have checked existing issues, online documentation and the Troubleshooting Guide

Replies: 11 comments · 2 replies

Uh oh!

P-R-O-C-H-Y Apr 15, 2025 Maintainer

Uh oh!

tvixen Apr 15, 2025 Author

Uh oh!

P-R-O-C-H-Y Apr 15, 2025 Maintainer

Uh oh!

tvixen Apr 15, 2025 Author

Uh oh!

tvixen Apr 15, 2025 Author

Uh oh!

Uh oh!

P-R-O-C-H-Y Apr 15, 2025 Maintainer

Uh oh!

tvixen Apr 15, 2025 Author

Uh oh!

Uh oh!

P-R-O-C-H-Y Apr 15, 2025 Maintainer

Uh oh!

P-R-O-C-H-Y Apr 15, 2025 Maintainer

Uh oh!

Uh oh!

tvixen Apr 15, 2025 Author

Uh oh!

P-R-O-C-H-Y Apr 15, 2025 Maintainer

Uh oh!

tvixen Apr 15, 2025 Author

Uh oh!

Uh oh!

tvixen May 2, 2025 Author

tvixen
Apr 14, 2025

Replies: 11 comments 2 replies

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

tvixen
Apr 15, 2025
Author

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

tvixen
Apr 15, 2025
Author

tvixen
Apr 15, 2025
Author

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

tvixen
Apr 15, 2025
Author

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

P-R-O-C-H-Y
Apr 15, 2025
Maintainer

tvixen
Apr 15, 2025
Author

P-R-O-C-H-Y Apr 15, 2025
Maintainer

tvixen Apr 15, 2025
Author

tvixen
May 2, 2025
Author