home-assistant · Tommatheussen · Feb 21, 2025 · Feb 21, 2025 · Feb 26, 2025 · Feb 26, 2025
diff --git a/source/_integrations/satel_integra.markdown b/source/_integrations/satel_integra.markdown
@@ -8,6 +8,9 @@ ha_category:
   - Switch
 ha_release: 0.54
 ha_iot_class: Local Push
+ha_config_flow: true
+ha_codeowners:
+  - '@Tommatheussen'
 ha_domain: satel_integra
 ha_platforms:
   - alarm_control_panel
@@ -25,7 +28,7 @@ The `satel_integra` {% term integration %} will allow Home Assistant users who o
 There is currently support for the following device types within Home Assistant:
 
 - Binary sensor: Reports on zone or output statuses
-- Switch: allows for setting states of selected outputs 
+- Switch: allows for setting states of selected outputs
 - Alarm control panel: represents the zones (in Polish: "strefa"). Reports its status, and can be used to arm/disarm the partition
 
 The module communicates via Satel's open TCP protocol published on their website. It subscribes for new events coming from alarm system and reacts to them immediately.
@@ -40,133 +43,23 @@ A list of all partition, zone and output IDs can be acquired by running DloadX p
 
 For the binary sensor, check the [type/class](/integrations/binary_sensor/) list for a possible visualization of your zones. Note: If no zones or outputs are specified, Home Assistant will not load any binary_sensor integrations."
 
-## Configuration
+{% include integrations/config_flow.md %}
 
-A `satel_integra` section must be present in the {% term "`configuration.yaml`" %} file.
-{% include integrations/restart_ha_after_config_inclusion.md %}
+{% configuration_basic %}
+Host:
+  description: The IP address of the Satel Integra ETHM module.
+Port:
+  description: The port on which the ETHM module listens for clients using integration protocol.
+Code:
+  description: Optional code that will be used to toggle switchable outputs.
+{% endconfiguration_basic %}
 
-```yaml
-# Example configuration.yaml entry
-satel_integra:
-  host: IP_ADDRESS
-```
+## Partitions, zones, and outputs
 
-{% configuration %}
-host:
-  description: The IP address of the Satel Integra ETHM module on your home network, if using socket type.
-  required: true
-  default: localhost
-  type: string
-port:
-  description: The port on which the ETHM module listens for clients using integration protocol.
-  required: false
-  default: 7094
-  type: integer
-code:
-  description: User password, it's needed for making use of the switchable_outputs. It's recommended not to use admin password.
-  required: false
-  type: string
-partitions:
-  description: List of the partitions to operate on.
-  required: false
-  type: [integer, list]
-  keys:
-    name:
-      description: Name of the partition.
-      required: true
-      type: string    
-    arm_home_mode:
-      description: The mode in which the partition is armed when 'arm home' is used. Possible options are `1`,`2` or `3`. For more information on what the differences are between them, please refer to Satel Integra manual.
-      required: false
-      default: 1
-      type: integer
-zones:
-  description: "This parameter lists the zones (or inputs) that will be visible by Home Assistant. For each zone, a proper ID must be given as well as its name. The name is arbitrary and does not need to match the one specified in Satel Integra alarm configuration."
-  required: false
-  type: [integer, list]
-  keys:
-    name:
-      description: Name of the zone.
-      required: true
-      type: string
-    type:
-      description: The zone type.
-      required: false
-      default: motion
-      type: string
-outputs:
-  description: "Very similar to zones, but with outputs. Satel Integra uses outputs to inform external systems about different events. For example power failure, or that alarm started counting for exit or some other user-defined condition. They may be used for simple alarm-based automation. For more information please refer to Satel homepage and forums."
-  required: false
-  type: [integer, list]
-  keys:
-    name:
-      description: Name of the output.
-      required: true
-      type: string
-    type:
-      description: The type of the device - just for presentation.
-      required: false
-      default: motion
-      type: string
-switchable_outputs:
-  description: "Switchable outputs. These will show up as switches within Home Assistant."
-  required: false
-  type: [integer, list]
-  keys:
-    name:
-      description: Name of the output.
-      required: true
-      type: string
-{% endconfiguration %}
-
-## Full examples
+After setting up the connection details, partitions, zones, and outputs can be configured as **Subentries** on the {% my integration domain="satel_integra" title="**Satel Integra**" %} integration page.
 
-```yaml
-# Example configuration.yaml entry
-satel_integra:
-  host: 192.168.1.100
-  port: 7094
-  partitions:
-    01:
-      name: "House"
-      arm_home_mode: 2
-    02:
-      name: "Garage"
-  zones:
-    01:
-      name: "Bedroom"
-      type: "motion"
-    02:
-      name: "Hall"
-      type: "motion"
-    30:
-      name: "Kitchen - smoke"
-      type: "smoke"
-    113:
-      name: "Entry door"
-      type: "opening"
-  outputs:
-    05:
-      name: "Garden lights trigger"
-      type: "light"
-    09:
-      name: "Gate opening trigger"
-      type: "opening"
-    30:
-      name: "Alarm triggered"
-      type: "safety"
-    32:
-      name: "Alarm power problem"
-      type: "safety"
-  switchable_outputs:
-    05:
-      name: "Gate open"
-    06:
-      name: "Gate close"    
-    14:
-      name: "Garden light"
-
-```
+Click the 'Add partition', 'Add zone', 'Add output' or 'Add switchable output' buttons to create the respective entities and follow the config flow to set up the individual entities.
+Each partition will have its own alarm panel. Each zone and output will have a binary sensor, and a switch will be created for each switchable output.
 
 Having configured the zones and the outputs, you can use them for automation, such as to react on the movement in your bedroom.
 For example: