Miletus Documentation Manual

The technical manual for this device gives instructions for its installation, commissioning, and operation. However, the manual cannot cover all conceivable circumstances or include detailed information on all topics. In the event of questions or specific problems, do not take any action without proper authorization. Contact the appropriate Schneider Electric technical sales office and request the necessary information.

2015

Chapter 3 (reference documentation) of Yade-DEM documentation [1] [1] Smilauer V. et al. (2015). Yade Documentation 2nd ed. doi:10.5281/zenodo.34073. http://yade-dem.org

ok

Nr -No. KI/EAB/RWB/Z Marie Lundberg 2/001 59-EN/LZT 720 0024 Uen Dokansv/Godkänd -Doc respons/Approved Kontr -Checked Datum -Date Rev File

2A)0A/QMWLK MCKHO ࡍࠫ ዎዌዌዒᐕዔዕᣣ‫ޓ‬᳓ᦐᣣ‫ޓ‬ඦᓟዏᤨዏዔಽ Indicates the need to follow proper procedures and to pay attention to precautions so that efficient service is provided. Provides additional information to help you to perform the repair efficiently. 2A)0A/QMWLK MCKHO ࡍࠫ ዎዌዌዒᐕዔዕᣣ‫ޓ‬᳓ᦐᣣ‫ޓ‬ඦᓟዏᤨዏዔಽ GENERAL INTRODUCTION (J08E) GN01-7 6. UNIT (1) This manual uses the SI unit system. The SI unit is an international unit which is based on one unit per quantity unlike the conventional unit system which differs from country to country, in order to facilitate technology exchange. (2) This manual writes the SI unit and a conventional unit side by side, the conventional unit enclosed in parentheses { }. *1: X is a value obtained by converting 1 [conventional unit] to an SI unit and is used as a conversion factor of the conventional unit and SI unit. *2: The torque conversion value may depend on the unit. Follow the specific value described for each unit. SI unit Conventional unit Conversion value* 1 (1[Conventional unit] = X [SI unit]) SI unit Conventional unit Conversion value* 1 (1[Conventional unit] = X [SI unit]) Force N kgf 1 kgf=9.80665 N Spring constant N/mm kgf/mm 1 kgf/mm= 9.80665 N/mm Torque* 2 N⋅m kgf⋅cm 1 kgf⋅cm= 0.0980665 N⋅m Volume L cc 1 cc=1 mL Pressure Pa kgf/cm 2 1kgf/cm 2 = 98.0665 kPa= 0.0980665 Mpa Efficiency W PS 1 PS=0.735499 kW mmHg 1mmHg=0.133322 kPa Quantity of heat W⋅H cal 1 kcal=1.13279 W⋅h Rotation speed r/min. rpm 1 rpm=1 r/min. Fuel consumption ratio g/W⋅h g/PS⋅h 1 g/PS⋅h= 1.3596 g/kW⋅h min.-1 1 rpm=1 min.-1 2A)0A/QMWLK MCKHO ࡍࠫ ዎዌዌዒᐕዔዕᣣ‫ޓ‬᳓ᦐᣣ‫ޓ‬ඦᓟዏᤨዏዔಽ PRECAUTIONS FOR ELECTRICAL SYSTEM 1. REMOVING THE BATTERY CABLE (1) Before electrical system work, remove the cable from the minus terminal of the battery in order to avoid burning caused by shortcircuiting. (2) To remove the battery cable, fully release the nut to avoid damage to the battery terminal. Never twist the terminal. 2. HANDLING OF ELECTRONIC PARTS (1) Never give an impact to electronic parts of a computer or relay. (2) Keep electronic parts away from high temperatures and humidity. (3) Never splash water onto electronic parts in washing the vehicle. 3. HANDLING OF WIRE HARNESS (1) Perform marking on a clamp and a clip and secure then in original position so that the wire harness will not interfere with the end and acute angle section of the body and a bolt.

Una macro son un conjunto de instrucciones que sirven para automatizar procesos. Refiriéndonos a excel, supongamos que realizamos frecuentemente la acción de seleccionar un rango para aplicarle negrita, cambio d e fuente y centrado. En lugar de hacer estas acciones manualmente, se puede elaborar una macro e invocarla para que ejecute los tres procesos automáticamente.