F1 submachine gun
| F1 | |
|---|---|
| Type | Submachine gun |
| Place of origin |  Australia |
| Service history | |
| In service | 1963–1991 |
| Used by | See Users |
| Wars | Vietnam War Rhodesia, Operation Agila |
| Production history | |
| Designed | 1962 |
| Manufacturer | Lithgow Small Arms Factory |
| Produced | July 1963 |
| Number built | 25,136 |
| Specifications | |
| Weight | 3.7 kg (Empty) 4.30 kg (Loaded) |
| Length | 714 mm |
| Barrel length | 198 mm |
|
|
|
| Cartridge | 9×19mm Parabellum |
| Caliber | 9 mm |
| Action | Blowback, Open bolt |
| Rate of fire | 600–640 rounds/min |
| Effective firing range | 150 m |
| Maximum firing range | 100–200 m |
| Feed system | 34-round Sterling SMG compatible box magazine |
| Sights | Offset iron sights |
The 9×19mm Parabellum F1 was a standard Australian submachine gun manufactured by the Lithgow Small Arms Factory.[1] It was designated the X3 while under development. First issued to Australian troops in July 1963, it replaced the Owen machine carbine. The F1 was retired in the early 1990s and replaced by the F88C Austeyr, an Australian-built version of the Steyr AUG rifle with slight modifications. The F1 had a robust and simple design and proved useful in close-quarter fighting during the Vietnam War. However, in Vietnam it was largely replaced by the American 5.56mm M16A1 rifle owing to the 9mm achieving poor penetration through brush and bamboo. Some 25,000 were produced by Lithgow from 1962–73. Malaysia bought a small number of the F1 but this only totaled 28 in number.
Design details
The F1 is a simple blowback design firing from an open bolt with a fixed firing pin. It shares many design features with the British Sterling submachine gun. Unlike both the Sterling and its predecessor, the Owen, the F1 has a removable wooden butt and pistol grip. A curved, detachable 34-round box magazine is inserted in a magazine housing on top of the barrel, similar to the earlier Owen gun. It used the same magazine as the Sterling. The top-mounted magazine is unobtrusive for carry and when lying prone. Lightning fast magazine changes can be made;, it has the added advantage of only needing a light spring being no harder to load than a .22 magazine not requiring special mag fillers like its contemporaries and to be less likely to jam than a bottom mounted magazine.[citation needed] The ejection port is directly under the magazine and provides a trap for the unwary user; should the user's hand stray back to the port, the bolt moving forwards will 'bite' the web of the hand. The butt-plate and pistol-grip are identical to those on the L1A1 SLR as well as the capability of adapting SLR bayonets. However, it was mostly used with a detachable spike bayonet fitted on the right side of the barrel jacket.
The trigger is a two-stage pull, half back semi auto, pull and hold back gives full auto requiring a safety catch only easily operated by the thumb. There is a small guard fitted forward of the ejection port to protect the forward hand. The left-mounted cocking handle has a tab that, when pressed, locks into the bolt, enabling it to be worked backwards and forwards to clear fouling. The pistol grip with internal parts came from the production line of the SLR L1A1 rifle, at the Lithgow factory. The wooden butt also was from the SLR production line, reducing the amount of tooling.
Stripping is simple: Safety on, remove magazine, cock and hold bolt open, rotate to left, inspect bolt face and chamber, release bolt under control. Then grab butt, press catch on bottom of receiver with other hand rotate butt to left 90 degree pull off, remove spring, release safety tip barrel up pull trigger bolt slides out. Assemble in reverse. Suggested ranges for use were 25 meters from the hip snap shooting 100 meters using sights.
Because of the vertical magazine the sights of the F1 were offset to the right of the weapon requiring a slight head tilt to the right, the rear sight being a roughly triangular asymmetrical metal flap with a round aperture, the front sight being a blade mounted on the right side of the weapon's magazine well.
Users
Accessories
The Complete Equipment Schedule (CES) for the F1 included:
- a large round wire and nylon brush, similar to a bottle brush for cleaning the tubular body of the weapon
- a standard SLR pull-through (a string with a loop at one end for holding a piece of service flannelette and a weight at the other to assist the user in feeding it down the barrel)
- a sling similar to the standard brass and canvas SLR sling, but shorter
- a detachable spike bayonet
- 5 magazines and
- a 4 magazine pouch, each pocket having its own flap.
Notes
- ↑ Modern Firearms' F1 submachine gun. Retrieved on 28 July 2007.
References
- Australian Service Machine Guns (Skennerton)
- S.A.I.S No.3, 9mm Owen & Austen MK I* (Skennerton)
- Various Factory Records, S.A.F. Lithgow
- Infantry Training Vol. 1, Infantry Platoon Weapons Pam.
