S-II

For the functionally-defined brain region, see Secondary somatosensory cortex.

S-II

The S-II stage during stacking operations of Apollo 6 in the VAB
Manufacturer	North American
Country of origin	USA
Used on	Saturn V (stage 2) Saturn INT-21 (stage 2)
General characteristics
Height	82 ft (24.9 m)
Diameter	33 ft (10 m)
Gross mass	480,900 kg (1,060,000 lb)
Engine details
Engines	5 J-2 engine
Thrust	1,000,000 pounds-force (4,400 kN)
Burn time	367 seconds
Fuel	LOX/LH2

The S-II (pronounced "ess two") was the second stage of the Saturn V rocket. It was built by North American Aviation. Using liquid hydrogen (LH2) and liquid oxygen (LOX) it had five J-2 engines in a quincunx pattern. The second stage accelerated the Saturn V through the upper atmosphere with 1,000,000 pounds-force (4,400 kN) of thrust.

History

S-2 assembly building in Seal Beach, CA

The beginning of the S-II came in December 1959 when a committee recommended the design and construction of a high-thrust, liquid hydrogen fueled engine. The contract for this engine was given to Rocketdyne and it would be later called the J-2. At the same time the S-II stage design began to take shape. Initially it was to have four J-2 engines and be 74 feet (23 m) in length and 260 inches (6.6 m) in diameter.

In 1961 the Marshall Space Flight Center began the process to find the contractor to build the stage. Out of the 30 aerospace companies invited to a conference where the initial requirements were laid out, only seven submitted proposals a month later. Three of these were eliminated after their proposals had been investigated. However it was then decided that the initial specifications for the entire rocket were too small and so it was decided to increase the size of the stages used. This raised difficulties for the four remaining companies as NASA had still not yet decided on various aspects of the stage including size, and the upper stages that would be placed on top.

In the end on 11 September 1961 the contract was awarded to North American Aviation (who were also awarded the contract for the Apollo Command/Service Module), with the manufacturing plant built by the government at Seal Beach, California.

Configuration

Cutaway illustration of the S-II (second) stage

When fully loaded with propellant, the S-II had a mass of about 481 tonnes. The hardware was only 7.6% of this—92.4% was liquid hydrogen and liquid oxygen.

At the bottom was the thrust structure supporting five J-2 engines. The center engine was fixed, while the other four were gimballed.

Instead of using an intertank (empty container between tanks) like the S-IC, the S-II used a common bulkhead (similar to that of the S-IV and S-IVB stages) that included both the top of the LOX tank and bottom of the LH2 tank. It consisted of two aluminium sheets separated by a honeycomb structure made of phenolic resin. It insulated a 70 °C (125 °F) temperature differential between the two tanks. The use of a common bulkhead saved 3.6 tonnes in weight.

The LOX tank was an ellipsoidal container of 10 meters diameter and 6.7 meters high holding up to 377.35 cubic meters (83,000 gallons) of propellant. It was formed by welding 12 gores (large triangular sections) and two circular pieces for the top and bottom. The gores were shaped by positioning in a 211,000 liter tank of water with three carefully orchestrated sets of underwater explosions to shape each gore.

The LH2 tank was constructed of six cylinders: five were 2.4 meters high and the sixth 0.69 meter high. The biggest challenge was the insulation. Liquid hydrogen must be kept colder than about 20 °C above absolute zero (20 K or −252 °C or −423 °F) so good insulation is very important. Initial attempts did not work well: there were bonding issues and air pockets. The final method was to spray insulation on by hand and trim the excess. The LH2 tank volume was 1182 cu.m. (260,000 gal.).

The S-II was constructed vertically to aid welding and keep the large circular sections in the correct shape.

Stages built

Serial number	Use	Launch date	Current location	Notes
S-II-F	Used as Dynamic Test Stage replacement after destruction of S-II-S/D and S-II-T		At the U.S. Space & Rocket Center, Huntsville, Alabama
S-II-T				Destroyed by accident during pressure testing May 28, 1966
S-II-D	Construction canceled
S-II-S/D	Structural and Dynamic Test Vehicle			Destroyed in test stand September 29, 1965
S-II-1	Apollo 4	November 9, 1967		Carried "Camera Targets" spaced around the forward skirt and carried cameras to record first stage separation
S-II-2	Apollo 6	April 4, 1968		Carried cameras to record first stage separation, similar to Apollo 4. Two engines failed during ascent due to pogo oscillation and incorrect engine control wiring.
S-II-3	Apollo 8	December 21, 1968
S-II-4	Apollo 9	March 3, 1969		1800 kg lighter allowing 600 kg more payload, more powerful engines and carried more LOX
S-II-5	Apollo 10	May 18, 1969
S-II-6	Apollo 11	July 16, 1969
S-II-7	Apollo 12	November 14, 1969
S-II-8	Apollo 13	April 11, 1970		Inboard engine failed during ascent due to pogo oscillation.
S-II-9	Apollo 14	January 31, 1971
S-II-10	Apollo 15	July 26, 1971
S-II-11	Apollo 16	April 16, 1972
S-II-12	Apollo 17	December 7, 1972
S-II-13	Skylab 1	May 14, 1973		Modified to act as the terminal stage. The only S-II to enter earth orbit, made an uncontrolled reentry into the Atlantic on January 11, 1975.
S-II-14	Apollo 18 (cancelled)	N/A	Apollo-Saturn V Center, Kennedy Space Center	From the cancelled Apollo 18 mission.
S-II-15	Skylab 1 backup (not flown)	N/A	Johnson Space Center	From SA-515 the Skylab backup vehicle which NASA did not use.

See also

• S-IC
• S-IVB
• Apollo (spacecraft)
• MS-II

References

• Apollo Saturn Reference Page